goldfish-ranchu.pdf
(
95 KB
)
Pobierz
Ranchu.PDF
Ranchu (Ornamental Goldfish)
c
Ronald Koh - 1994
1.
2.
3.
A 12 to 15 cm square of
paper will do nicely. Fold
in half and unfold.
Fold and unfold vertically,
creasing the centre only.
Fold to the mark made in
step 2 and unfold, creasing in
the centre only.
4.
5.
6.
... then fold down again.
7.
Fold and unfold again as
shown. This marks an
eighth of the height.
Bring the bottom edge of
the paper to the crease
made in step 4 ...
8.
9.
Fold and unfold each
corner, creasing well.
10.
Inside reverse fold along
creases made in step 7.
Turn paper over.
Fold down ...
11.
12.
13.
... and again on the right.
Turn over again
Fold the diagonal edges of
the paper to the line in the
middle, crease firmly, and
unfold.
14.
15.
Bring down this layer ...
... like this, then rabbit,s ear both sides
along creases made previously.
16.
17.
18.
19.
Turn over.
Open out this
layer to the right.
Lift out the hidden
paper at the top,
then open out the
layer on the left.
Fold up the lower portion of
the assembly as shown.
20.
21.
22.
Valley fold ...
... then crimp fold each
side.
Fold assembly in half while
lifting out the layer at the
top and a triangle at the
bottom ...
23.
24.
1/4
25.
... like this ...
... and this.
Rotate the
model
Fold the first two flaps to the
right, and crease firmly.
26.
27.
28.
Now valley fold ...
... then unfold Steps 25 and 26.
Lift up the first layer ...
29.
30.
31.
... then fold in the left corner
along creases made in
Step 26.
Fold the next layer on the left
to the right as illustrated ...
... then bring down the top flap as
you valley fold the assembly on
the left along creases made in
Step 25 ...
32.
33.
34.
... like this.
Repeat Steps 25 to 31 on the
other side.
Fold down the first layer ...
... then reverse fold the
resulting corner as
shown.
35.
36.
37.
Bring up the top layer again ...
... then valley fold the next
layer ...
... and then valley fold again
and crimp as illustrated.
38.
39.
40.
Now bring down the layer at
the top again and repeat
Steps (?) to 37 on the other
side.
Crimp fold according to
diagrammed proportions,
crease firmly ...
... and unfold.
41.
42.
43.
Bring up the top layer again.
Crimp fold each of the four
layers separately as shown,
then close the assembly by
bring the top layer down again.
Fold up as shown ...
44.
45.
46.
... then down again.
Repeat at the back from
here through Step 47 ...
... then crimp fold as
illustrated.
Now open out to unfold
Steps 43 to 45.
47.
48.
49.
Collapse the assembly
under the body as shown,
using crease lines made
previously.
Your model should now
look like this.
Valley fold, creasing
firmly ...
... and yet again.
The illustration is
slightly enlarged from
here on.
50.
51.
... and yet again.
Now unfold Steps 49 and 50.
52.
53.
Hidden between the external body layers
are two narrower pleated layers. Push up
from the bottom to open out the pleat of
the hidden layer nearest to you, while
simultaneously separating the first and
second layers at the top ...
... like this.
Now crimp fold both sides of the
head along creases made
previously while bringing out the
top of the head ...
55.
56.
54.
Crimp fold both sides of the model
to form the mouth.
Fold and unfold at the top of
the head, creasing firmly.
Mountain fold at the base of
the neck.
Now sink at the top of the
head, then continue folding
as illustrated.
57.
58.
59.
Valley fold to the left again ...
... then unfold Steps 56 and 57.
Separate the two layers of
this flap and crimp fold along
creases made previously.
Plik z chomika:
Jussy_S
Inne pliki z tego folderu:
grasshopper.pdf
(37 KB)
compactdragon.pdf
(18 KB)
flapbird.pdf
(6 KB)
coot.pdf
(5 KB)
giantspidercrab.pdf
(195 KB)
Inne foldery tego chomika:
Książki
Kwiaty
Łódki
Programy
Przykłady_Origami_Foto
Zgłoś jeśli
naruszono regulamin