Inne.doc

Asko
Washing Machine

Display

Condition

Remedy

F1

Water Supply/low water fill

·         Check water supply to machine

·         Replace water inlet valve

F2

Water level too high

·         Plugged/Bad water pump

·         Faulty water valve

F3

Pump Problem

Check pump trap and clean.

F4

Thermistor problem

·         Open thermistor, replace

·         Bad wiring to thermistor

F5

Fault in thermal cutout or heating pause fault. Selected temperature not reached in 90 minutes

·         Check heating element

·         Check thermostat

F6

Motor Fault

·         Check wiring to motor

·         Replace motor if necessary

F7

Door lock release fault

·         Bent pull-rod for door latch

·         Bad door latch solenoid

00 00

Machine did not spin

Check load for out of balance, Redistribute load and restart

GE
WSL Model Washing Machine

Display

Condition

Remedy

IE - Water level sensor error

Water sensor fails to send signal for longer than 5 seconds.

Press POWER button. No other buttons work:

·         Check wiring harness

·         Check pressure sensor switch

·         Check circuit board

7E - Water supply error

No frequency change for 60 minutes from water supply.

Press POWER button. No other buttons work:

·         check wiring harness

·         Check water valve

·         Check pressure sensor switch

·         Check circuit board

E - Drain pump error

Water level does not decrease to reset point within 15 minutes from draining water from the washer.

Press POWER button. No other buttons work:

·         Check wiring harness

·         Check pump motor

·         Check circuit board

dE - Lid open error

Lid is open during wash cycle.

Close lid.

·         Check wiring harness

·         Check lid switch

·         Check unbalance switch

·         Check circuit board

UE - Unbalance switch error

Unbalanced load is sensed three times during a spin operation.

Open lid. Prevalence load and close lid.

·         Check wiring harness

·         Check lid switch

·         Check unbalance switch

·         Check circuit board

OE - Water overflow error

Water supply does not stop after sensing an overflow condition.

Turn off household water supply to washer and unplug power cord.

·         Check wiring harness

·         Check water inlet valve

·         Check pressure sensor switch

·         Check circuit board

Kitchen Aid Washer Fault Codes
Front Loading Automatic Washer Fault Codes
(Model KHWS01PMT/WH)

Display

Condition

Remedy

F/H

No water detected entering machine or Pressure switch trip not detected.

If after 30 seconds the control does not detect water entering machine, valves will be turned off and the error code will be displayed.

OR

If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash.

Press PAUSE/CANCEL twice to clear the display.

·         If there is no water in the unit:
1. Make sure that both valves at the water source(s) are turned on all the way.
2. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves
3. Verify inlet valve operation

·         If there is no water in unit:
1. Verify drain pump operation.
2. Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch.
3. Verify there is not a siphon problem.
4. Unplug washer or disconnect power.
5. Verify wire harness connections to inlet valves, pressure switch, drain pump, flow meter, and Central Control Unit (CCU)
6. Check all hoses for possible leaks.
7. Plug in washer or reconncect power.
8. Verify pressure switch operation.
9. Verify flow meter operation by blowing air through the part and measureing the resistance.
10. Verify CCU operation by running a Diagnostic test or any cycle.
Replace failed component.

F02

Long Drain

If the drain time exceeds 8 minutes, the water valves are turned off and "F02" is flashed.

NOTE: After 4 minutes the "Sud" error will be displayed, then 4 minutes later the F02 error code will be displayed.

Press PAUSE/CANCEL twice to clear the display.

1. Check the drain hose and make sure it is not plugged or kinked.
2. Unplug washer or d...