jewelry pattern wire ring.pdf

WIRE JEWELRY MAKING

PATTERN #105

Adjustable Filigree Gold Ring

Project 105 is an adjustable gold ring -- wear it on any finger or on a toe. These rings can be

made in just a few minutes and because they are adjustable, they can be sold on the spot. It is

best made with gold filled 21 gauge square half hardwire.

SUPPLIES NEEDED

• 18 inches of 14kt. gold filled 21 gauge square half hard wire or brass practice wire

TOOLS NEEDED

• flat nose pliers

• chain nose pliers

• wire cutter or flush cutter

• Sharpie marking pen

• steel ruler

• steel ring mandrel

• rawhide hammer

PRICING YOUR FINISHED PROJECT

Cost of material-----(prices are approximate)

• 18 in. 14kt. gold filled 21 gauge square half hard wire $1.50

Suggested retail price $10.00-15.00

Let's get started:

• Cut four pieces of 21 gauge gold filled square half hard

wire--each 3-1/2 inches long. These will be the wires of

your ring.

• Cut two pieces of 21 gauge gold filled square half hard

wire --- each 2 inches long. These will be your wrap

wires.

• Lay the four 3-1/2 inch long shank wires together.

• TIP: Wrap the center of the bundle with masking tape to

help hold your wires together.

• Using your flat nose pliers, make a small hook about 3/4

inch long on the end of one wrap wire.

• Measure 3/4 of an inch from one end of the bundle,

place the hook around the bundle, and start making two

complete wraps around the bundle. Cut the excess wires

off on the backside of the ring shank. See DIAGRAM #1.

• Next measure 3/4 of an inch from the other end of the

bundle and make two complete wraps using the second

wrap wire. Cut off the excess wires on the backside of

the ring shank.

• This is what your bundle should look like. See DIAGRAM

#2.

DIAGRAM #1

DIAGRAM #2

• Using a smooth kitchen knife, start on one end of the

bundle and bend the end wires one by one in an outward

direction. See DIAGRAM #3.

• Using your knife, bend the wires one by one outward in

the opposite direction on the other end of the bundle.

• The bundle with bent wires should look like this. See

DIAGRAM #4.

DIAGRAM #3

DIAGRAM #4

• Start with one end of the bundle and work from the left to

the right. Do not cut the wire on the far left at all. Cut off

1/8 inch from the wire next to the far left wire. Then cut

1/4 inch off of the next wire and cut 3/8 inch off of the

last wire.

• With your chain nose pliers, catch the tip of the shortest

wire and start to curl the wire outwards around itself.

This is the beginning of a rosette. Always start with the

shortest wire. See DIAGRAM #5

• Press the curl flat with your flat nose pliers and start to

turn the wire into a coil. See DIAGRAM #6.

DIAGRAM #5

DIAGRAM #6

• Continue to roll the wire into a complete coil--a small

rosette and flatten the rosette with your flat nose pliers.

• Working from the shortest to the longest wire, begin a

small curl with the next wire, flatten the curl and continue

to make a rosette in the next wire. Bring the rosette right

up to the first rosette and flatten it.

• Make a rosette on the next wire bringing the rosette right

up to the last rosette. And make a rosette on the last

wire.

• This is what the rosettes should look like. See DIAGRAM

#7.

DIAGRAM #7

• Using your pin vise, twist each of the wires at the

opposite end of the bundle. See DIAGRAM #8.

• Now clip the wires on the other end of the bundle, cutting

them opposite of the other end -- the shortest wire on

other end will be the longest wire on this end. Do NOT

cut the long wire. Cut 1/8 inch off the next wire. Cut 1/4

inch off the next wire and cut 3/8 inch off the last wire.

• This is what your bundle should look like. See DIAGRAM

• With your flat nose pliers, make a rosette facing

outwards on the shortest wire. Flatten the rosette and

continue to make a rosette on each wire working from

the shortest wire to the longest wire. Your finished

rosettes should look like this. See DIAGRAM 10.

DIAGRAM #8

DIAGRAM 9

DIAGRAM 10

• Put your bundle on the ring mandrel at about 5-1/2 and

bend it completely around your ring mandrel. See

DIAGRAM 11.

• Flatten and gently shape your ring by putting it on the

ring mandrel and tapping it with a rawhide hammer.

• TIP: By starting with a smaller size, you will be able to

easily open the ring up to a larger size ring by pushing

the ring to a larger size on the mandrel. If you start with

a larger size ring, you will not be able to make the ring

smaller.

DIAGRAM #11

• The finished adjustable filigree gold ring.

• NOTE: This project produces a ring that will fit sizes 6-

1/2 to 11-1/2. To make a smaller ring, use 3 inch long

wires for the bundle.

• NOTE: To make a toe ring, use only 3 wires instead of 4

wires.

DIAGRAM #12

Pattern created by Master Wire Sculptor Preston J Reuther.

“Start Your Own Home Jewelry

Business Today!”

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: