RF_Power_Amplifiers.pdf

RF Power Amplifiers

Iulian Rosu, YO3DAC / VA3IUL, http://www.qsl.net/va3iul

RF Power Amplifiers are used in a wide variety of applications including Wireless

Communication, TV transmissions, Radar, and RF heating.

The basic techniques for RF power amplification can use classes as A, B, C, D, E, and

F, for frequencies ranging from VLF (Very Low Frequency) through Microwave

Frequencies.

RF Output Power can range from a few mW to MW, depend by application.

The introduction of solid-state RF power devices brought the use of lower voltages, higher

currents, and relatively low load resistances.

Most important parameters that defines an RF Power Amplifier are:

1. Output Power

2. Gain

3. Linearity

4. Stability

5. DC supply voltage

6. Efficiency

7. Ruggedness

•

Choosing the bias points of an RF Power Amplifier can determine the level of performance

ultimately possible with that PA. By comparing PA bias approaches, can evaluate the trade-

offs for: Output Power, Efficiency, Linearity, or other parameters for different applications.

The Power Class of the amplification determines the type of bias applied to an RF

power transistor.

•

The Power Amplifier’s Efficiency is a measure of its ability to convert the DC power of

the supply into the signal power delivered to the load.

•

The definition of the efficiency can be represented in an equation form as:

or Power Added Efficiency:

• Power that is not converted to useful signal is dissipated as heat. Power Amplifiers

that has low efficiency have high levels of heat dissipation, which could be a limiting

factor in particular design.

• In addition to the class of operation, the overall efficiency of a Power Amplifier is

affected by factors such as dielectric and conductor losses. First quantify any loss in

the circuit, then attempt to minimize it, and finally ensure that the mechanical and

thermal design is adequate under all conditions.

Power Classes

Class - A

Is defined, as an amplifier that is biased so that the output current flows at all the

time, and the input signal drive level is kept small enough to avoid driving the transistor in

cut-off. Another way of stating this is to say that the conduction angle of the transistor is

360 , meaning that the transistor conducts for the full cycle of the input signal. That makes

Class-A the most linear of all amplifier types, where linearity means simply how closely the

output signal of the amplifier resembles the input signal.

Always have to remember this:

•

No transistor is perfectly linear; however the output signal of an amplifier is never an exact

replica of the input signal.

Linear amplification is required when the signal contains AM – Amplitude Modulation

or a combination of both, Amplitude and Phase Modulation (SSB, TV video carriers,

QPSK, QAM, OFDM).

•

Signals such as CW, FM or PM have constant envelopes (amplitudes) and therefore do not

require linear amplification.

The DC-power input is constant and the efficiency of an ideal Class-A PA is 50 % at

PEP.

•

The DC power consumption of a Class-A amplifier is independent of the output signal

amplitude.

•

P DC = V CC 2 / R = V CC x I CQ and I CQ ~ I MAX / 2

The amplification process in Class-A is inherently linear, hence increasing the

quiescent current or decreasing the input signal level monotonically decreases IMD

and harmonic levels.

•

Since both positive and negative excursions of the drive affect the drain current, it has

the highest gain of any PA.

•

The absence of harmonics in the amplification process, allows Class-A to be used at

frequencies close to the maximum capability (fmax) of the transistor. However, the

efficiency is low. Class-A PAs are therefore typically used in applications requiring low

power, high linearity, high gain, broadband operation, or high-frequency operation.

•

The efficiency of real Class-A Pas is degraded by the on-state resistance or saturation

voltage of the transistor. It is also degraded by the presence of load reactance, which

in essence requires the PA to generate more output voltage or current to deliver the

same power to the load.

η (Efficiency_Class-A) = Max_Load_Voltage / (2*V cc 2 )

•

One important thing to mentioned is that: small signal S-parameters can be used in

simulations if the large-signal amplifier is operating in Class-A.

•

Class - B

This is an amplifier in which the conduction angle for the transistor is approximately 180 .

•

Thus the transistor conducts only half of the time, either on positive or negative half

cycle of the input signal.

The same as in Class-A, the DC bias applied to the transistor determines the Class-B

operation.

•

Class-B amplifiers are more efficient than Class-A amplifiers. The instantaneous

efficiency of a Class-B PA varies with the output voltage and for an ideal PA reaches

π/4 (78.5 %) at PEP. However they are much less linear. Therefore a typical Class-B

amplifier will produce quite a bit harmonic distortion that must be filtered from the

amplified signal.

•

P DC = (2*V CC *V) / (Π*R);

P LOAD = V 2 / (2*R);

η (Efficiency_Class-B) = (Π*V) / (4*V CC )

Common configuration of Class-B amplifier is push-pull amplifier. In this configuration one

transistor conducts during positive half cycles of the input signal and the second transistor

conducts during the negative half cycle. In this way the entire input signal is reproduced at

the output.

A single transistor may be used in a Class-B configuration. The only requirement in

this case is that a resonant circuit must be placed in the output network of the transistor in

order to “reproduce” the other half of the input signal.

In practice, the quiescent current is on the order of 10 % of the peak collector current

and adjusted to minimize crossover distortion caused by transistor nonlinearities at low

outputs.

•

In theory 6dB or more drive power is needed to achieve Class-B compared with Class-

A. In practice this 6dB reduction in power gain is lower; for BJT amplifiers is lower than

FETs, approximately 2dB.

•

The efficiency of the push-pull power amplifier is the same as that of the single ended

power amplifier with the same conduction angle, and the output power capability of the

push-pull power amplifier is twice that of the single-ended power amplifier (3dB

higher).

•

In the push-pull arrangement, the DC components and even harmonics cancel, but

odd harmonics add, thus the output contains the fundamental only. Note that the

cancellation of odd harmonics is only valid if the amplifier is not driven hard.

•

Class - AB

This amplifier is a compromise between Class-A and Class-B in terms of efficiency

and linearity.

The transistor is biased typically to a quiescent point, which is somewhere in the region

between the cutoff point and the Class A bias point, at 10 to 15 percent of I Cmax .

In this case, the transistor will be ON for more than half a cycle, but less than a full cycle of

the input signal.

• Conduction angle in Class-AB is between 180 and 360 and Efficiency is between 50

% and 78.5 %

• Class-AB has higher efficiency than Class-A at price of linearity.

• Class-AB is not a linear amplifier; a signal with an amplitude-modulated envelope will

be distorted significantly at this peak power level. The reason is in fact that in Class-

AB operation the conduction angle is a function of drive level.

Experimentally was found that Class-AB often offers a wider dynamic range than either

Class-A or Class-B operation. This is because gain compression in Class-AB comes from a

different, and additional, source than Class-A. Saturation effects are primarily caused by the

clipping of the RF voltage on the supply rails.

Linearizing the response of a BJT PA in Class-AB includes the use of specific, and

very low, impedance for the base bias supply voltage. This is a very different bias

design issue in comparison to the simple current bias used in small signal BJT

amplifiers, or the simple high impedance voltage bias used in FET PA’s.

•

Running the PA in a mid-AB condition the power gain may be 3dB higher than Class-

•

Conventional Class-AB operation incurs odd degree nonlinearities in the process of

improving efficiency. Theoretically to increases efficiency all the way up to 78.5 %, the

device shall generate only even order nonlinearities. Such a device will not generate

undesirable close-to-carrier intermodulation distortion.

•

Class - C

Is an amplifier where the conduction angle for the transistor is significantly less than 180 .

•

The transistor is biased such that under steady-state conditions no collector current

flows.

The transistor idles at cut-off. Class C Amplifier

•

Linearity of the Class-C amplifier is the poorest of the classes of amplifiers.

•

The Efficiency of Class-C can approach 85 %, which is much better than either the

Class-B or the Class-A amplifier.

•

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: