Cabinet - TV game hideway (on wheels).pdf - Projekty - stolarstwo - woocash85

TV game hideaway

Build a nifty TV, video and games storage unit

are the main entertainment centres

in most homes but they can look

messy. This neat cabinet hides away all

the bits and pieces. They stay plugged

in, ready to use any time, and you can

even play games with the drawer shut.

Here’s how

Step 1 Pair up sides, top and shelves.

Partly drive 40mm nails into one edge,

150mm apart and nip off heads. Apply

glue to both edges, align sides and

clamp tightly. Let dry overnight.

Step 2 Round top front edges of sides

(A). Measure down 90 and 310mm to

tops of shelf housings. Clamp straight

edge to panels to use a router with

a 19mm straight bit to cut 5mm-deep

housings to 20mm from front edge.

Make sides as mirror images. Rout

19mm x 5mm-deep rebate on back

of board

down to top housing.

Step 3 Cut cleats (B). Screw to bottom

of sides, centred between front and

back. From bottom of sides, measure up

110 and 280mm and rule across. Attach

cabinet member of runners so top edge

is flush with line, back is flush with side

backs.

to back of cabinet with bottom of cut-out

flush with top of back rail.

Step 7 Plane drawer fronts (K, L) to

height. On top edge of bottom one, mark

300 x 10mm deep rebate, round ends

and cut out with jigsaw. Clamp to front of

drawer, then screw on from back. For top

drawer, partly drive in screws so points

show through front. Press drawer face

against points to mark position, partly

predrill holes and screw on. Plane faces

as necessary.

Step 4 Cut a 5 x 30mm notch at front

corners of top and shelf (C). Stand one

side on edge, apply glue to edge of top

and slide into housing. Screw in from

sides.

Step 6 Prepare drawers by routing a

5mm x 19mm wide rebate at the ends of

sides (G). Using a 6mm straight bit and

a routing fence, run a 5mm-deep groove

finishing 10mm from the bottom edge.

Glue and screw sides to front and

back (H) so bases align with top

of groove. Width of drawer should

allow 12.5-13mm either side for drawer

runners. Slide in drawer bottom (I) and

screw to front and back. Inside the

bottom drawer, mark 165mm from ends

and screw in place two dividers (J). Add

drawer member of runners.

Step 5 Cut out design of decorative

back (D) with jigsaw. Screw between

sides in rebate cut at back of sides.

Screw two bottom rails (E) between

sides at base.

Measure 300mm from each side of

backing panel (F), then measure up

45 and 220mm from bottom. Mark out

rectangle and cut out with jigsaw. Nail

Step 8 Plug screw holes, smooth.

Apply two coats of polyurethane. Add

drawer handles and drill holes on

underside of cleats for sockets and

castors.

See Buying Guide

T he TV and video-games console

What you will need

Item Part Size Material

A1 Sides (2) 285 x 19 x 700mm Tasmanian oak

A2 Sides (2) 235 x 19 x 700mm Tasmanian oak

B Cleats (2) 50 x 30 x 482mm Maple

C1 Top/shelf (2) 285 x 19 x 900mm Tasmanian oak

C2 Top/shelf (2) 235 x 19 x 900mm Tasmanian oak

D Decorative back 120 x 19 x 900mm Tasmanian oak

E Rails (2) 50 x 19 x 890mm Tasmanian oak

F Backing panel 918 x 380 x 3mm Plywood

G Drawer sides (4) 140 x 19 x 500mm Maple

H Drawer front/back (4) 120 x 19 x 836mm Maple

I Drawer bottom (2) 500 x 836 x 6mm Plywood

J Dividers (2) 120 x 19 x 462mm Maple

K Top drawer face 151 x 19 x 888mm Tasmanian oak

L Bottom drawer face 165 x 19 x 888mm Tasmanian oak

You will also need two pairs of 500mm bottom-mount, full-extension drawer

runners; assorted screws and nails; PVA adhesive; four socket-fitting

50mm twin-wheel castors; four drawer handles. Some timbers need to be

ripped or planed to width. All joints are glued and screwed unless otherwise

indicated. All screws in sides are counterbored to suit 10mm wood plugs.

Cabinet - TV game hideway (on wheels).pdf

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: