5L i kilka innych.pdf

AXTECH

Te c hnical Instructions

Printers

OEM Info

Tools

CORPORATE

LOS ANGELES

T 800 394.9900

818 316.0656

F 800 394.9910

818 313.9568

HP Laserjet 5L/5ML

HP Laserjet 6LSE/6LXI

HP Laserjet 3100

Canon LBP-460

Canon Laser Class

4000/4500 (FX3)

Part Number: C3906A

Gram Load: 140 grams

Yield @ 5%: 2500 pgs

Pages/Min.: 4ppm

Resolution: 600 dpi

Funnel

Diagonal Pliers

Needle Nose Pliers

Phillips #2 Screwdriver

Small Flat Blade Screwdriver

140 Grams of 5L Toner

Damp Cloth

Soft Lint-Free Cloth

ATLANTA

T 877 676.4223

770 516.9488

F 877 337.7976

770 516.7794

Photo 1

Step 1

Place the AX cartridge on a table with the

handle facing up. Using diagonal pliers,

pull the steel lock pin from one end and

then the other. The cartridge separates

into waste hopper and toner hopper

halves. Place the toner hopper aside.

(See Photo 1)

DALLAS

T 877 499.4989

972 840.4989

F 877 774.1750

972 840.1750

MIAMI

T 800 595.4297

305 594.3396

F 800 522.8640

305 594.3309

Photo 2a

Step 2

Using needle nose pliers, grasp the metal

drum axle (at the notch) on the large gear

end of the waste hopper, while holding

the hopper securely with the other hand.

Now, simply pull the pin straight out and

set it aside.

(See Photo 2a)

Grasp the drum gear, lift it up, and pull the

drum straight out. Wrap the drum in pro-

tective cloth or paper and set it aside.

(See Photo 2b)

NEW YORK

T 800 431.7884

631 345.0121

F 800 431.8812

631 345.0690

TORONTO

T 877 848.0818

905 712.9501

F 877 772.6773

905 712.9502

Photo 2b

SYDNEY

T 02 9648.2630

F 02 9648.2635

Brand names and trademarks are the

properties of their respective holders

and are for descriptive use only.

Te chnical Resource Center:

Toll Free:

800 394.9900

Website:

www.futuregraphicsllc.com

AX Technical Instructions

Photo 3

Step 3

Remove the primary charge roller (PCR)

from its clips and set it aside. Note that

this roller is similar to the 5P in that it has

a much more pliable covering than the

harder PCRs found in the LX and PX car-

tridges and is easily damaged.

(See Photo 3)

Photo 4

Step 4

Remove the two wiper blade screws with

a Phillips screwdriver. Now, using needle

nose pliers, grasp the upward angled

edge of the wiper blade lifting upwards

and out.

(See Photo 4)

Next, clean the wiper blade with a damp

cloth (or, wiper blade cream) and set it

aside. The waste hopper can now be

emptied and vacuumed. In doing so, be

careful not to damage the recovery blade.

Step 5

Reassemble the waste hopper by following the above steps in reverse order. Put the

wiper blade back in and tighten the two screws gently. Wipe all toner from the PCR with

the damp cloth and dry it with the soft, lint-free cloth. Put the PCR back into its clips.

Install a new drum (or, a clean OEM drum) and both axles. Set aside with the drum cov-

ered.

Photo 6

Step 6

Examine the toner hopper. There are gears

at one end and the bias connector at the

other. One screw on each end holds the

end caps. Both caps can be removed if

you’re curious, but only the non-gear end

needs to be taken off. With this end facing

you, remove the screw.

(See Photo 6)

Photo 7

Step 7

Remove the end cap from the waste hop-

per and clean old conductive grease from

the contact spring and plate. Set the end

cap aside and remove the small white plas-

tic mag roller bushing.

(See Photo 7)

Need trust-worthy, detailed Technical

Instructions for another engine?

V isit: www.futuregraphicsllc.com

AX Technical Instructions

Photo 8

Step 8

Grasp the mag roller with your right

hand, while holding the toner hopper

securely with your left. Lift it upwards

and to the right.

(See Photo 8)

Photo 9

Step 9

Remove the large white plastic bushing and

drive gear from the left. Then remove the

two screws from the doctor blade and lift

the blade out.

(See Photo 9)

NOTE: Avoid breaking off the small locat-

ing pin on the left.

Photo 10

Step 10

Remove the fill plug, empty out any

remaining toner and vacuum, making

sure not to damage the lower mylar strip.

Clean all toner from the mag roller clean-

er. Insert seal.

(See Photo 10)

NOTE :The black square guide in the seal

exit slot may be removed to facilitate seal

installation, and then reinserted.

Photo 11

Step 11

Re-install the doctor blade on the waste

hopper and insert and tighten screws.

Drop the drive gear back into its slot-

with the notch on the flat area facing to

the left.

(See Photo 11)

Now, put the long white plastic bushing

on the left end of the mag roller by

grasping the right end of the mag roller,

lay it down into the hopper and slide the

shaft into the white plastic guide on the

left. Turn the mag roller until the flat side

of the shaft matches the flat area of the

gear, and insert into position.

Need help with a particular remanu-

facturing problem?

Call the Technical Resource Center from

8am - 5pm PST: 800 394.9900

AX Technical Instructions

Photo 12

Step 12

Hold the toner hopper in one hand with

your thumb on the shiny area of the mag

roller to keep it in position. A funnel will

help you fill the hopper from a toner bot-

tle.

(See Photo 12)

Step 13

Replace the fill plug. Put the small white plastic bushing on the right end of the mag

roller. Now place the end cap over the plug and align the “D” shaped hole with the

mag roller shaft by turning the mag roller gear on the other end. Insert and tighten

the last remaining screw.

Photo 14

Step 14

Finally, fit the two halves together, align-

ing the springs on the toner hopper with

the positioning pins on the waste hopper.

(See Photo 14)

Align the matching holes on each end by

pressing the springs against their seats,

and insert and press home the locking

pins.

Comparing Operating Specifications

OEM No.

Toner

Drum

PCR Shaft

Cartridge

OEM

PPM of Pages

OEM

Fill

Diameter

Length

PCR

Length

Type/Model

Ctg. #

@ 5%

Density

(grams)

(mm)

Rubber

(inches)

AX/5L

C3906A

2,500

1.46

140

245

Soft

9.54

PX/4L, 4P

92274A

3,000

1.52

160

257

Hard

9.46

VX/5P, 5MP C3903A

4,000

1.52

225

257

Soft

9.54

LX/2P

92275A

3,500

1.43

225

254

Hard

9.46

Need trust-worthy, detailed Technical

Instructions for another engine?

V isit: www.futuregraphicsllc.com

Te chnical Resource Center:

Toll Free:

800 394.9900

Website:

www.futuregraphicsllc.com

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: