Table Saw Outfeed Support.pdf
(
5594 KB
)
Pobierz
OUTFEED
SUPPORT
© 2009 August Home Publishing Co.
f
eaTure
p
rOjecT
T
able
S
aw
O
uTfeed
S
uppOrT
This easy-to-build addition to your table saw takes the hassle out of
cutting long boards and sheet goods.
A
dding an outfeed support to
your table saw is like gain-
ing an extra pair of hands
in the shop. It provides sturdy sup-
port for your workpiece whether
you’re ripping a long board or cut-
ting plywood down to size.
The outfeed support shown in
the photo provides this plus a few
key features. For instance, slots in
the top allow you to use your miter
gauge without removing it.
A leveler at the end of each leg
lets you make ine height adjust-
ments. This means you can align
the top to your saw table to com-
pensate for any unevenness in the
loor of your shop.
To connect the outfeed sup-
port to your table saw, cleats hook
over a wood rail on the back rail of
the saw. (I’ve included mounting
options for the two most common
types of fence arrangements.) And
since the legs fold up, the support
table can be quickly removed and
hung on the wall for storage.
1
www.Woodsmith.com
© 2009 August Home Publishing Co. All Rights Reser ved.
plastic laMiNatE cuts
dowN oN FRictioN aNd
allows woRkpiEcE
to slidE sMoothly
acRoss top
Construction Details
Overall Dimensions:
18" x 36"x 34"
dadoEs Match MitER
gaugE slots oN
saw tablE
plywood top
pRoVidEs stablE
outFEEd suppoRt
FoR Easy attachMENt
aNd REMoVal, clEats
oN thE top Fit oVER a
wood Rail MouNtEd
oN thE saw
stop holds
lEgs iN VERtical
positioN
Notch iN tablE allows
MoVEMENt oF bladE
guaRd/splittER FoR
aNglEd cuts
SIDE VIEW
(CLOSED)
lEg assEMbly
attachEs to
thE tablE with
utility hiNgEs
lEgs
Fold Flat
FoR Easy
stoRagE
SIDE VIEW
(OPEN)
sizE thE lENgth oF
thE lEgs to Match
thE suppoRt to thE
hEight oF youR saw
lEgs Fit
sNugly
agaiNst
stop
{
A wood rail attached to the back
of the table saw holds the outfeed
support in place.
SECtION
VIEW
(LEVELEr)
lEVElERs allow
adJustMENt FoR
uNEVEN shop
FlooRs
thREadEd iNsERt
Materials
18
x36-#/4Ply.
A
Top(1)
B
HingePlate(1)
#/4x2!/2-22
C
LegStop(1)
#/4x2!/2-28
D
FrontCleats(4)
#/4x#/4-17
E
Legs(2)
1!/2x1!/2-36(Rough)
F
Stretchers(2)
#/4x2!/2-16!/2
When not in use,
the table folds up
for easy storage.
G
SawRail(2)
#/4x2-18
•(1)18"x36"PlasticLaminate
•(2)3"UtilityHingeswithScrews
•(2)LevelingFeet
•(2)%/16"ThreadedInserts
•(11)#8x3"FhWoodscrews
•(14)#8x1!/4"FhWoodscrews
2
www.Woodsmith.com
© 2009 August Home Publishing Co. All Rights Reser ved.
1
Building the Support
An outfeed support should be sta-
ble enough and large enough to
catch a workpiece as it slides off
the saw. And this design ills the
bill on both counts. The folding leg
assembly and solid connection to
the table saw provide a strong base.
And with the 18" by 36" top, you’ll
have plenty of worksurface.
Table Top.
I used
3
⁄
" plywood for the
top because it’s lat, inexpensive,
and resists warping. And by adding
laminate, you get the extra beneit of
a low-friction surface.
You can start by cutting the top to
size and rounding off the back cor-
ners. I also cut a notch on the front
edge of the table for the blade guard
(see the box below).
Next, I glued on an oversized
piece of laminate and trimmed the
edges with a router and a lush trim
bit. The laminate creates a durable
surface for the table.
Top DaDoes.
To complete the table
top, you’ll need to cut a couple of
dadoes. Align these slightly oversize
dadoes to match the miter slots on
your table saw so the miter gauge
has clearance as you make a cut, as
shown in the left margin photo.
leg sTop.
Now turn the top over and
add hardwood support pieces to
2
FIGURE
{
A dado slightly
wider than the
miter slot provides
clearance for the
miter gauge bar.
hold the legs. I started by attaching
a leg stop to help stabilize the legs
and keep them properly positioned
while the table is being used. This
stop is just a piece of
3
⁄
"-thick hard-
wood that’s screwed to the top.
Hinge plaTe.
The next step is to add
a mounting plate for the leg assem-
bly. Simply center the hinge plate
along the inside edge of the leg
stop and attach it with screws, as
you see in Figure 2.
NOTCH & ATTACHMENT
There are a couple things that can
make adding an outfeed support
a little tricky. First, you’ll need to
provide clearance for the blade
guard/splitter assembly. As you
can see in the photo, I cut a 2"-
wide slot " deep to accommo-
date the splitter angled to 5°.
The second challenge is
mounting the outfeed support to
your saw. On many saws, there’s
a steel fence rail running along
the back edge. In this case, it’s
just a matter of drilling a few
holes in the rail and attaching a
wood rail with screws.
The drawings at right show
how the cleats on the outfeed
support it over the rail to hold
the support in place. You can
simply adjust the width of the rail
until the top is level. If your saw
has tube-style fence rails, take a
look at the next page for an alter-
nate mounting method.
‹
A wide
notch in the
top provides plenty of
clearance for the splitter
assembly.
No. ???
Woodsmith
3
www.Woodsmith.com
© 2009 August Home Publishing Co. All Rights Reser ved.
3
FIGURE
LEg ASSEMBLy
A simple leg assembly holds the back
of the outfeed support. The legs are
connected by a pair of stretchers.
And the top stretcher attaches the
legs to the hinge plate.
legs.
The legs are cut from 1
1
⁄
2
"-
thick stock. You’ll need to size the
length of the legs to it your saw. To
do this, just measure from the loor
to the top of your saw. Then sub-
tract 2
1
⁄
2
" to determine the length of
the legs. (The 2
1
⁄
2
" accounts for the
thickness of the top, the hinge plate,
and the leg levelers.)
After cutting each leg to length,
I drilled a hole for the threaded
insert that holds the leveler in the
bottom of the leg. Then, you can
soften the edges at the router table
with a
1
⁄
8
" roundover bit.
sTreTcHers.
To add strength to the
assembly and prevent racking, I
connected the legs with a pair of
stretchers. After cutting the stretch-
ers to size, you can attach them with
long screws, as shown in Figure 3.
The next step is to fasten the legs
to the top. To do this, irst screw the
hinges to the top stretcher, then to
the hinge plate on the table. This is
shown in detail ‘a.’
Now the legs can be folded up
for storage. You can easily hang the
outfeed support on a wall. Just hook
CLEATS
D
it on a bracket sized to it under the
upper stretcher and between the
legs of the support.
cleaTs.
All that remains now is to
attach the support to your saw. This
design uses a simple and effective
method for mounting the outfeed
support. It consists of a pair of
cleats fastened along the front edge
of the top, as shown in Figures 2
and 3. These cleats it over a wood
rail you’ll attach to the rear of your
table saw. The thing to remember
when adding the cleats is to space
them to get a snug it over the rail
to hold the outfeed support steady,
even under heavy loads.
MounTing rail.
The last thing you’ll
need to do is add a wood rail to the
rear fence rail of your saw. How you
go about this depends on the type
of fence rail system on your saw.
The box below and the one on the
previous page cover the two most
common options.
a.
b.
TUBE-STyLE ATTACHMENT
Attaching the outfeed support to a
saw with tube-style rails presents
a real challenge. You can’t fasten
anything to the tube without inter-
fering with the movement of the
fence. So, the irst step is to add
metal brackets to the saw. They’ll
hold the saw rail that attaches to the
outfeed support. You should add a
bracket to each bolt that holds the
tube to the saw.
To make the metal brackets, I
used 1"-wide strips of
3
⁄
16
"-thick
steel. I star ted by cutting the
steel strips to length (about 6
1
⁄
2
")
and drilling holes for the mount-
ing bolts. Then, I made the 90°
bend in the steel by securing the
piece upright in a vise and pound-
ing it over lat.
Now it’s just a matter of drilling
holes and attaching the saw rails
using screws (drawings at right).
SAW RAIL
#/4" x 2" - 18"
G
‹
To mount the
cleat on a tube-
style fence, bolt
on a few simple,
shop-made
metal brackets.
No. ???
Woodsmith
5
www.Woodsmith.com
© 2009 August Home Publishing Co. All Rights Reser ved.
Plik z chomika:
klewier
Inne pliki z tego folderu:
10 Rules for Case Assembly.pdf
(2023 KB)
17 Profiles - 3 Bits.pdf
(5498 KB)
5 Router Table Upgrades.pdf
(1544 KB)
7 Tips for Working With Plywood Tips.pdf
(5906 KB)
Adjustable Dado Jig.pdf
(2731 KB)
Inne foldery tego chomika:
Online Extras
Zgłoś jeśli
naruszono regulamin