FOFOC98GBB.PDF

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00

www.cobra.it

FORD

MOD. FOCUS

PETROL

DIESEL

YEAR 98 ﬁ

MAKE

ALARM/SIREN

POSITION

Position the modular system and the siren in the engine compartment, on the

battery bracket. Run the cables through the available rubber plug located on the

bulkhead that divides the engine compartment from the cabin, under the fuse box

on the right of the engine compartment.

CENTRAL UNIT POSITION

Position the modular systems and the modules behind the fuse box located under

the dashboard on the driver’s side.

POWER SUPPLY

+ 30: connect to the RED 3 mm 2 wire in the wiring harness from the multiway black

connector at the entrance to the fuse box.

- 31: connect with a ring terminal to one of the terminals coming out of the general

power supply behind the left lateral panel on the driver’s side.

IGNITION WIRE

Connect to the 1,5 mm 2 GREEN/RED wire in the wiring harness that comes out of

the 11 way grey connector at the rear of the fuse box located under the dashboard

on the driver’s side.

DIRECTION INDICATORS

Connect to the 1 mm 2 BLUE and BLUE/ORANGE wires in the wiring harness from

the 11 way black connector located behind the left-side bulkhead on the driver’s

side.

ELECTRIC WINDOWS

Driver’s window: Connect to the 1 mm 2 BLACK/RED wire.

Passenger’s window: Connect to the 1 mm 2 BLACK/RED wire.

Rear window, driver side: Connect to the 1 mm 2 BLACK/RED wire.

Rear window, passenger side: Connect to the 1 mm 2 BLACK/RED wire.

For total window roll up see diagram nr. 58.

CENTRAL DOORS LOCKING Negative control signal

Connect to the BLACK/ORANGE lock wire and BLACK/GREEN unlock wire in the

wiring harness under the driver’s floor trim.

IMMOBILISATION POINT

Fuel pump

Cut the 1 mm 2 BLACK/LIGHT BLUE wire in the wiring harness from the connector

of the relay marked “R7” at the fuse box in the engine compartment.

STARTER

+50: Cut the 2 mm 2 GREY/ORANGE wire in the wiring harness under the steering

column. Alternatively, in the black connector furthest to the left relative to the relays

at the fuse box under the dashboard.

BONNET SWITCH

Install an additional switch in the available hole on the right ledge of the engine

compartment.

DOOR SWITCH

Connect to the 1 mm 2 BLACK/YELLOW wire in the wiring harness under the

driver’s floor trim.

BOOT SWITCH

Connect to the 1 mm 2 RED/BLUE wire in the wiring harness under the driver’s floor

trim.

Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed

as per the instructions given on the product installation manual.

fofoc98gbb.doc

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00

www.cobra.it

FITTING DIAGRAM N°58

Diagram for windows locking (with automatism) on

FORD FOCUS and FORD FOCUS*

Bridge serie antitheft

+30

1052

1 2 3 4 5

brown/white

“+15” GREEN/YELLOW

ant left ant right post left post right

N° 4 diodes

type 1N4004

black/red black/orange

Operating central of windows automatism

(inside the driver’s side door)

These connections can be made directly in the connector coming out of the windows control switch located in the

driver’s side door. As the electric windows have the automatism, it is necessary to install the module Art. 1052 and the

4 diodes to avoid the current return harmful for the windows that are not used.

Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed

as per the instructions given on the product installation manual.

fofoc98gbb.doc

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: