how-to-make-danielle-9306-into-the-maya-pattern_original.pdf
(
4622 KB
)
Pobierz
194659155 UNPDF
How to make Danielle 9306 into the Maya
pattern
By: Benedikta
http://www.burdastyle.com/projects/how-to-make-danielle-9306-into-the-maya-pattern
This technique has no description.
Step 1
1. There are in total only three changes that have been made to the Danielle pattern to get the Maya pattern. No sleeves are
attached, the hem is shortened and the side seams are moved out a bit to make the skirt of the dress fuller.
Step 2
2. Look at your Pattern Print out and get familiar with all the pieces. You will be using all of them ( #1-#9) for the dress , except #7,
the sleeve pattern piece. On the left upper corner you have the back skirt piece (#6) and in the lower left hand corner the front skirt
piece (#3). Only those two pattern pieces will be modified in our how to.
Step 3
3.Here you see pattern piece # 7, the pattern piece for the sleeves, which is the one that you donât need for the Maya Dress. Make
sure to put it aside before cutting, in order to avoid wasting fabric.
Step 4
4. Next are the adjustments on the skirt. Take pattern piece # 3 (Front of Skirt), determine where the line for the side seam of your
size is. (Make sure to measure yourselve carefully before choosing your size.) The Side Seam is opposite to the seam that is
marked as center front / cut on fold. It is the slightly curved line on the top of the photo
Step 5
5. Find the point where your side seam intersects with the hemfoldline. From this point, (I used the sideseam of size 44 for my how
to) extend the hemline perpendicular to the side seam.Make a mark on that line at 3/4 â ( 2 cm )away from the original side seam.
Step 6
6. Connect the point that you just created in a straight line with the widest point of the hip. The wides part of the hip is right where
the curve of the hip turns into the straight line.
Step 7
6. Follow the same steps on the Back of the Skirt (pattern piece #6), but be aware that the side seam is on the other side then on
the Front Skirt, opposite from the Back center seam.
Step 8
7. Follow the same procedure than on the Front piece, by connecting the marked point with the widest point of the hip in a straight
line
Step 9
8. Back to the Front Skirt piece( #3) I will show you how to adjust the hem.
Remember however that the amount that I shortened the dress for our shoot, may not be enough or too much for your own height or
taste . Measure on yourself from the waist down where you want the hem to be. According you determine how much to shorten that
hem, by measuring down from the marks of the waist on the pattern. If you are not sure how long the hem should be rather give to
much and shorten it later.
Step 10
9. Move the hemline as well as the hemallowance line both up for 1 ½ (3.8 cm). Draw the new hemfold and hemallowance parallel
to the old lines into the pattern.
Step 11
10. Same procedure for the Back Skirt piece ( #6)
Step 12
11. Again, move hemfold and hem allowance up for 1 ½ (3.8cm) and draw in new line parallel to the old ones across the pattern.
Now you finished all the pattern changes that needed to be done. Before you start cutting you should however make sure that the
adjusted side seams of front and back match in their length, to avoid mistakes or unexact measuring. If everything matches you are
good to go.
Step 13
Good luck and lots of fun, while creating your own Maya.
How to make Danielle 9306 into the Maya pattern
Plik z chomika:
hazelleyes86
Inne pliki z tego folderu:
burda summer dress pattern+instructions.pdf
(429 KB)
Ellinor top pattern(1).pdf
(2911 KB)
Marisa dress pattern.pdf
(348 KB)
Marisa dress instructions.pdf
(241 KB)
Weisn Dirndl pattern.pdf
(1798 KB)
Inne foldery tego chomika:
3
4
Baletnica
biustonosze
BLUZKI - LATA 60 , 70
Zgłoś jeśli
naruszono regulamin