DSC-R1_L2_V1.0.PDF

DSC-R1

SERVICE MANUAL

LEVEL 2

US Model

Canadian Model

AEP Model

UK Model

E Model

Australian Model

Hong Kong Model

Chinese Model

Korea Model

Japanese Model

Tourist Model

Ver 1.0 2005.10

Revision History

How to use

Acrobat Reader

Link

SPECIFICATIONS

BLOCK DIAGRAMS

PRINTED WIRING BOARDS

SERVICE NOTE

FRAME SCHEMATIC DIAGRAM

REPAIR PARTS LIST

DISASSEMBLY

SCHEMATIC DIAGRAMS

• Precaution on Replacing the SY-132 Board

• Note for Disassemble Lens Assemble Repair (EK01A)

The components identified by

mark 0 or dotted line with

mark 0 are critical for safety.

Replace only with part num-

ber specified.

Les composants identifiés par une

marque 0 sont critiques pour la

sécurité.

Ne les remplacer que par une pièce

portant le numéro spécifié.

DIGITAL STILL CAMERA

DSC-R1_L2

2005J0500-1

Published by DI Technical Support Department

9-876-898-31

Sony EMCS Co.

Link

SPECIFICATIONS

Camera

[System]

Image device 21.5 × 14.4 mm color CMOS

sensor, Primary 3-color filter

Total pixel number of camera

Approx. 10 784 000 pixels

Effective pixel number of camera

Approx. 10 286 000 pixels

[LCD screen]

LCD panel 5.1 cm (2.0 type) TFT drive

Total number of dots

134 000 (560

240) dots

AC-L15A AC Adaptor

Input rating 100 V to 240 V AC, 50/60 Hz,

18 W

Output rating 8.4 V DC*

*See the label on the AC

Adaptor for other

specifications.

Operating temperature range

0°C to +40°C (32°F to +104°F)

Storage temperature range

-20°C to +60°C (-4°F to

+140°F)

Maximum dimensions

Approx. 56 × 31 × 100 mm

(2 1/4 × 1 1/4 × 4 inches) (W/H/

D), excluding projecting parts

Mass Approx. 190 g (6.7 oz)

excluding power cord (mains

lead)

Rechargeable battery pack NP-FM50

Used battery Lithium-ion battery

Maximum voltage

[Finder]

LCD panel 1.1 cm (0.44 type) TFT drive

Total number of dots

235 200 (980 × 240) dots

[Power, general]

Used battery pack

Lens

Carl Zeiss Vario-Sonnar T *

5× zoom lens

f = 14.3

120mm when converted to a

35 mm still camera)

F2.8 − 4.8

Filter diameter: 67 mm

Exposure control Automatic, Shutter speed

priority, Aperture priority,

Manual exposure, Scene

selection (4 modes)

White balance Automatic, Daylight, Cloudy,

Fluorescent, Incandescent,

Flash, One-push

File format (DCF compliant)

Still images: Exif Ver. 2.21

JPEG compliant, RAW (SR2),

DPOF compatible

Recording media “Memory Stick”

Microdrive

CompactFlash card (TypeI/

Typ eI I)

Flash Recommended distance (ISO

set to Auto): approx. 0.5 m to

8.5 m (1 feet 7 3/4 inches to 27

feet 10 3/4 inches) (W)/approx.

0.4 m to 5.0 m (1 feet 3 3/4

inches to 16 feet 4 7/8 inches)

(T)

Viewfinder Electric viewfinder (color)

[Input and Output connectors]

VIDEO OUT jack

71.5 mm (24

−

Rechargeable battery pack

NP-FM50

Power requirements

7.2 V

Power consumption (during shooting with LCD

on)

1.7 W

Operating temperature

0°C to +40°C (+32°F to

+104

(When using the Microdrive:

C to +40

C (41

F to

+104°F))

Storage temperature

−

DC 8.4 V

Nominal voltage DC 7.2 V

Capacity

C to +60

C (

−

F to

8.5 Wh (1 180 mAh)

+140°F)

Dimensions (lens: W-end)

139.4

156.0 mm

(5 1/2 × 3 7/8 × 6 1/4 inches)

(W/H/D, excluding protrusions)

Mass Approx. 1047 g (2 lb 4.9 oz)

(including NP-FM50 battery

pack, “Memory Stick”,

shoulder strap, and lens hood,

etc.)

Speaker Dynamic speaker

Exif Print Compatible

PRINT Image Matching III

Compatible

97.7

Design and specifications are subject to change

without notice.

Minijack

1 Vp-p, 75 Ω, unbalanced, sync

negative

ACC jack Mini-minijack (ø 2.5 mm)

USB jack mini-B

USB communication

Hi-Speed USB (USB 2.0

compliant)

PictBridge

Compatible

DSC-R1_L2

— 2 —

−

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

SAFETY-RELATED COMPONENT WARNING!!

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH

MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered

connections. Check the entire board surface for solder splashes

and bridges.

2. Check the interboard wiring to ensure that no wires are

"pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly

transistors, that were installed during a previous repair. Point

them out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs

of deterioration. Point them out to the customer and

recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. FLEXIBLE Circuit Board Repairing

• Keep the temperature of the soldering iron around 270°C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Unleaded solder

Boards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

•

Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350°C.

Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

•

Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than

ordinary solder so use caution not to let solder bridges occur such

as on IC pins, etc.

•

Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

DSC-R1_L2

— 3 —

TABLE OF CONTENTS

Section

Title

P a ge

Section

Title

P a ge

1. SERVICE NOTE

1-1. Description on Self-diagnosis Display ···························· 1-1

1-2. Precaution on Replacing the SY-132 Board ···················· 1-2

1-3. Note when Replacing the Lens Block,

CMOS Block and Optical Filter Block ··························· 1-3

2. DISASSEMBLY

2-1. Disassembly ····································································· 2-3

2-2. The Method Of Attachment Of

PN-002 Flexible Board ···················································· 2-5

2-3. How To Disassemble BT Lid ·········································· 2-7

2-4. The Method Of Attachment Of BK-002 Board

and Control (Mode) Switch Block ·································· 2-7

3. BLOCK DIAGRAMS

3-1. Overall Block Diagram (1/3) ··········································· 3-1

3-2. Overall Block Diagram (2/3) ··········································· 3-3

3-3. Overall Block Diagram (3/3) ··········································· 3-5

3-4. Power Block Diagram (1/3) ············································· 3-7

3-5. Power Block Diagram (2/3) ············································· 3-9

3-6. Power Block Diagram (3/3) ··········································· 3-11

4. PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS

4-1. Frame Schematic Diagram ·············································· 4-1

4-2. Schematic Diagrams ························································ 4-5

4-3. Printed Wiring Boards ··················································· 4-43

4-4. Waveforms ····································································· 4-69

4-5. Mounted Parts Location ················································ 4-74

5. REPAIR PARTS LIST

5-1. Exploded Views ······························································· 5-2

5-2. Electrical Parts List ························································· 5-9

DSC-R1_L2

— 4 —

1. SERVICE NOTE

1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY

Self-diagnosis display

C: ss: ss

You can reverse the camera

malfunction yourself. (However,

contact your Sony dealer or local

authorized Sony service facility

when you cannot recover from the

camera malfunction.)

E: ss: ss

Contact your Sony dealer or local

authorized Sony service facility.

Display Code

Countermeasure

Cause

Caution Display During Error

C:32:ss

Turn the power off and on again.

Trouble with hardware.

SYSTEM ERROR

Format the recording medium.

Unformatted recording medium is inserted.

FORMAT ERROR

MEMORY STICK ERROR,

CF CARD ERROR

C:13:ss

Insert a new recording medium.

Recording medium is broken.

E:61:ss

Checking of lens drive circuit.

When failed in the focus and zoom

initialization.

—

Checking of flash unit or replacement

of flash unit.

Abnormality when flash is being

charged.

E:91:ss

DSC-R1_L2

1-1

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: