S7-300_FM355C-S_e.pdf

(3742 KB) Pobierz
FM 355 closed-loop control module
Introduction
SIMATIC FM 355 closed-loop control module
1
SIMATIC
2
FM 355 closed-loop control module
3
4
5
Operating Instructions
6
7
8
9
10
11
12
13
This manual is part of the documentation package
with order no: 6ES7355-0VH00-8BA0
A
B
Edition 02/2006
A5E00059344-03
C
D
Product Overview
Information for the controller
adjustment
How Does the FM 355
Control?
Installing and Removing the
FM 355
Wiring the FM 355
Parameter Configuration of
the FM 355
Implementing the FM 355 in
the User Program
Commissioning the FM 355
Properties of Digital and
Analog Inputs and Outputs
Connecting Measuring
Transducers and
Loads/Actuators
Assignment of the Instance
DBs
Faults and Diagnostics
Examples
FB 29 and FB 30
Data Sheet
Spare Parts
References
43517959.008.png 43517959.009.png
Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
Danger
indicates that death or severe personal injury will result if proper precautions are not taken.
Warning
indicates that death or severe personal injury may result if proper precautions are not taken.
Caution
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
Caution
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
Notice
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning and
operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes
in this documentation qualified persons are defined as persons who are authorized to commission, ground and
label devices, systems and circuits in accordance with established safety practices and standards.
Prescribed Usage
Note the following:
Warning
This device may only be used for the applications described in the catalog or the technical description and only in
connection with devices or components from other manufacturers which have been approved or recommended
by Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and
assembly as well as careful operation and maintenance.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG
Automation and Drives
Postfach 48 48
90437 NÜRNBERG
GERMANY
Order No.: A5E00059344-03
Edition 02/2006
Copyright © Siemens AG 2006.
Technical data subject to change
43517959.010.png 43517959.011.png 43517959.001.png 43517959.002.png 43517959.003.png
Introduction
Preface
Purpose of This Manual
This manual describes all the steps that are required to use the FM 355 function module. It
supports rapid and effective familiarization with the FM 355 functionality.
Contents of the Manual
This manual describes the hardware and software of the FM 355. It consists of an instruction
section and contains reference material (appendices.)
The following subjects are covered:
Fundamentals of controlling
Installing and removing the FM 355
Wiring the FM 355
Assigning parameters to the FM 355
Programming the FM 355
Appendixes
Target Group
This manual is intended for the following target groups:
Fitters
Programmers
Commissioning engineers
Service and maintenance personnel
Scope of This Manual
The present manual contains the description of function module FM 355 applicable at the
time the manual was published. We reserve the right to describe changes of FM 355
functionality in a Product Information leaflet.
FM 355 closed-loop control module
Operating Instructions, Edition 02/2006, A5E00059344-03
iii
Introduction
Approvals
The S7-300 has the following approvals:
UL Recognition Mark
Underwriters Laboratories (UL) in accordance with Standard UL 508
CSA-Certification-Mark
Canadian Standard Association (CSA) to Standard C 22.2 No. 142
FM approval complying with Factory Mutual Approval Standard Class Number 3611, Class I,
Division 2, Group A, B, C, D
Warning
Personal injury and material damage may be incurred.
In potentially explosive environments, there is a risk of injury or damage if you disconnect
any connectors while the S7-300 is in operation.
Always isolate the S7-300 operated in such areas before you disconnect and connectors.
Warning
WARNING - DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS LOCATION IS
KNOWN TO BE NONHAZARDOUS
CE Marking
Our products fulfill the requirements of the EU Directive 89/336/EEC ”Electromagnetic
compatibility”.
The EU conformity certificates are available for the relevant authorities and are kept at the
following address in accordance with the above-mentioned EU Directive. Article 10:
Siemens Aktiengesellschaft
Bereich Automatisierungs- und Antriebstechnik
A&D AS RD ST PLC
Postfach 1963
D-92209 Amberg
FM 355 closed-loop control module
iv
Operating Instructions, Edition 02/2006, A5E00059344-03
43517959.004.png 43517959.005.png 43517959.006.png
Introduction
Position in the Information Landscape
This manual is a component of the S7-300 and ET 200M documentation.
System
Documentation
S7-300 S7-300 Automation systems
Structure, CPU Data
S7-300, M7-300 Automation systems, Module specifications
S7-300 Operation List
ET 200M ET 200M Distributed I/O Device
S7-300, M7-300 Automation systems, Module Specifications
Guide
The manual contains the following guides which provide quick access to the specific
information you need:
At the beginning of the manual you can find a comprehensive list of contents.
Following the appendices, you will find a glossary in which important technical terms used
in the manual are defined.
The manual closes with a list of references and a detailed index for quick access to the
information you require.
Further Support
If you have any questions concerning the use of products which are not answered in this
manual, please contact your local Siemens partner at your Siemens office. A list of Siemens
representatives worldwide is contained, for example, in the appendix entitled "Siemens
Worldwide" of the manual "S7-300 Automation systems, Configuration of an S7-300.
We offer a range of courses to help get you started with the SIMATIC S7 programmable
controller. Please contact your local training center or the central training center in
Nuremberg, D-90327 Germany, Tel. +49 (0) 911 895 3200.
FM 355 closed-loop control module
Operating Instructions, Edition 02/2006, A5E00059344-03
v
43517959.007.png
Zgłoś jeśli naruszono regulamin