SINAUT_MD720-3.pdf

SIMATIC NET

Preface, Contents

GPRS/GSM-Modem

SINAUT MD720-3

Introduction

System manual

Inserting the SIM card

Connecting the device and

switching on the device

SINAUT MD720-3 in Terminal

Mode

SINAUT MD720-3 in OPC Mode

Service function

Technical Data

Glossary

C79000-G8976-C211

Release 02/2006

Safety Guidelines

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

! Danger

indicates that death or severe personal injury will result if proper precautions are not taken.

! Warning

indicates that death or severe personal injury may result if proper precautions are not taken.

! Caution

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

Caution

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

Notice

indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The device/system may only be set up and used in conjunction with this documentation. Commissioning and

operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes

in this documentation qualified persons are defined as persons who are authorized to commission, ground and

label devices, systems and circuits in accordance with established safety practices and standards.

Prescribed Usage

Note the following:

! Warning

This device may only be used for the applications described in the catalog or the technical description and only in

connection with devices or components from other manufacturers which have been approved or recommended

by Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and

assembly as well as careful operation and maintenance.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the

owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Siemens AG

Automation and Drives

Postfach 48 48

90437 NÜRNBERG

DEUTSCHLAND

Order No.: C79000-G8976-C211

Release 02/2006

Technical data subject to change

General

The product SINAUT MD720-3 complies with European standard EN60950, 05.2003,

Safety of Information Technology Equipment.

Read the installation instructions carefully before using the device.

Keep the device away from children, especially small children.

The device must not be installed or operated outdoors or at damp locations.

Do not operate the device if the connecting leads or the device itself are damaged.

External power supply

Use only an external power supply which also complies with EN60950. The output

voltage of the external power supply must not exceed 30VDC. The output of the

external power supply must be short-circuit proof.

Warning

The power supply unit to supply the SINAUT MD720-3 must comply with NEC Class 2

circuits as outlined in the National Electrical Code (ANSI/NFPA 70) only.

When connecting to a battery or accumulator, make sure that an all-pole circuit-

breaker (main battery switch) with sufficient selectivity and a fuse with sufficient

selectivity are provided between the device and the battery or accumulator.

Please pay regard to section 7 Technical Data of the system manual, as well as the

installation and utilisation regulations of the respective manufacturers of the power

supply, the battery or the accumulator.

SIM card

To install the SIM card the device must be opened. Before opening the device,

disconnect it from the supply voltage. Static charges can damage the device when it is

open. Discharge the electric static of your body before opening the device. To do so,

touch an earthed surface, e.g. the metal casing of the switch cabinet. Please pay

regard to section 2 Inserting the SIM card o f this system manual.

Handling cables

Never pull a cable connector out of a socket by its cable, but pull on the connector

itself. Cable connectors with screw fasteners (D-Sub) must always be screwed on

tightly. Do not lay the cable over sharp corners and edges without edge protection. If

necessary, provide sufficient strain relief for the cables.

For safety reasons, make sure that the bending radius of the cables is observed.

SINAUT MD720-3

C79000-G8976-C211

Failure to observe the bending radius of the antenna cable results in the deterioration

of the system's transmission and reception properties. The minimum bending radius

static must not fall below 5 times the cable diameter and dynamic below 15 times the

cable diameter.

Radio device

Warning

Never use the device in places where the operation of radio devices is prohibited. The

device contains a radio transmitter which could in certain circumstances impair the

functionality of electronic medical devices such as hearing aids or pacemakers. You

can obtain advice from your physician or the manufacturer of such devices. To

prevent data carriers from being demagnetised, do not keep disks, credit cards or

other magnetic data carriers near the device.

Installing antennas

Warning

The emission limits as recommended by the Commission on Radiological Protection

(13/14 September 2001) must be observed.

Installing an external antenna

Caution

When installing an antenna outdoors it is essential that the antenna is fitted correctly

by a qualified person. Lightning Protection Standard VDE V 0185 Sections 1 to 4, in

its current version, and further standards must be observed.

Lightning protection category for buildings

Caution

For outdoor installation, the antenna may be fitted only within the lightning protection

zones O/E or 1. These lightning protection zones are prescribed by the lightning

protection spherical radius.

SINAUT MD720-3

C79000-G8976-C211

The EMV lightning protection zone concept

Caution

The EMV lightning protection zone concept is to be observed. To avoid large induction

loops a lightning protection equipotential bonding is to be used. If the antenna or

antenna cable is installed near to the lightning protection system, the minimum

distances to the lightning protection system must be observed. If this is not possible,

insulated installation as described in VDE V 0185 Sections 1 to 4, in its current

version, is essential.

FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer / installer or an experienced radio/TV technician for help.

FCC Part 15.19

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. this device may not cause harmful interference, and

2. this device must accept any interference received, including interference that

may cause undesired operation.

SINAUT MD720-3

C79000-G8976-C211

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: