v143.pdf

(270 KB) Pobierz
679901952 UNPDF
A flying model of the latest
VOUGHT EXPORT FIGHTER
BY WALTER KAHN
Above -- The completed framework reveals the exactness with which the real ship has been duplicated.
Below -- The real ship which is a modification of original Vought V-143 fighter.
DESIGNED to conform with the United
States army specifications and listed by the
manufacturer, Chance Vought, as an export model,
the V-143 is a challenge to any other ship within its
class. Capable of doing close to three hundred miles
per hour, the V-143 is easily maneuvered and can
ably defend itself.
The construction of the model is simple,
entailing only the primary steps of model-aircraft
building. Before attempting to build the model it is
advisable. to read and thoroughly digest the
directions. By doing this, costly mistakes will be
avoided.
bulkheads are, all except #1, cut from 1/16" sheet
with the grain running vertically. In cutting out the
bulkheads only the four main notches need be cut.
The position of the intermediate stringers should be
marked. This procedure is suggested to enable proper
alignment of the stringers. After the four main
stringers are secured in place the notches for the
intermediate stringers are cut with a sliver of a two-
edged razor.
The complete cockpit cover frame is made
from 1/32" square bamboo. This frame is covered
with a sheet of celluloid. The portion between #4 and
#5 is covered with 1/32" sheet, and made to fit as
shown on the top and side view.
The tail block is cut to the shape shown on 3.
It is hollowed out to as thin a wall thickness as
possible. The wood for the tail block must be the
CONSTRUCTION
Fuselage may either be constructed in two
halves or else with complete bulkheads. The
679901952.001.png
lightest obtainable. The block is not cemented in
place until the stabilizer is secured.
Wing construction follows the same general
procedure for building most model wings. The wing
is constructed in one panel. Because of this it is
necessary to trace the half of the wing shown and use
it as the other half. The complete layout of half the
wing is gotten by connecting Sheet 2 with Sheet 4.
The ribs are all cut from 1/16" sheet. The wing is
constructed on the plan itself with the various parts
held in place by pins until the cement has set. As the
wing is tapered, both top and front, it is necessary to
taper the leading edge and spars accordingly. It is
suggested that the parts first be roughly shaped and
glued in place. After the wing is removed from the
plan the parts are then sanded to a smooth finish. The
wing tips are of bamboo and can best be formed over
a flame. If desired they can be wound with thread at
the leading and trailing edges.
Special attention should be given to the center
block. The block is not hollowed out as the bulk is
required to balance the completed model. The cross-
sectional shape is shown on the plan. It follows that of
the wing section, except it is extended farther forward
of the leading edge.
After the wing is completed, the outer wing
panels are broken at the point of the solid center block
to form the 1-1/4" dihedral. The joints are reglued.
Tail surfaces. The construction of both the
rudder and stabilizer is like that of the wing. It is
important that the lightest balsa wood be used in its
construction. (Due to the large moment arm of the
model a heavy tail will throw it out of complete
balance.) The spars used are 1/16" balsa rounded and
are made to run through the ribs as shown. The ribs of
the tail are first cut roughly to a streamline shape.
After the tail is completed they are sanded smoothly.
The tips are of bamboo. The bamboo used should not
be greater than 1/32" square.
Landing gear construction is extremely
simple, as it consists entirely of a single strut attached
to the wing as shown. The shape of the strut is shown
on Sheet 2. The strut is made in two parts and
attached by inserting the lower part into the top. The
axle is a piece of music wire bent to the shape shown;
it is glued and wound with thread for security. The
side cover of the strut is cut from 1/16" sheet balsa
and cemented to the strut.
Cowl shape is shown on Sheet 1. It is
hollowed out to house a 2-1/2"-diameter celluloid en-
gine. The cowl is held to the model by slipping onto a
special Bulkhead # 1 cut from 3/16" stock.
Flying propeller is shown on Sheet 5. It is a
three-bladed propeller. Each blade is carved
separately and inserted into a three-bladed hub as
shown. Care must be taken to see that all the blades
are attached with the same pitch angle, otherwise the
propeller will not-track. If desired, a scale propeller
may he used. The side view of such propeller, a
Hamilton Standard, is shown on Sheet 1. The front
view is of conventional metal propeller shape.
Motor stick is 1/8 x 1/4" stock. It is attached
to the celluloid engine as shown. The engine is held to
the cowl by small drops of cement on each cylinder.
The propeller shaft is then passed through the rear of
the engine. A ball-bearing washer is placed on the
shaft. Following this the propeller is placed on. The
shaft is bent to the shape shown on Sheet 5 and forced
into the hub of the propeller. A drop of glue will
secure the shaft to the prop. It is important that the
shaft be lined properly. This should be checked.
The rear hook is bent as shown. It is attached
to the motor stick by inserting the prong end of the
hook into the stick, wound and glued.
COVERING THE MODEL
Because most of the parts are attached directly
to each other they can be covered separately. The
model is covered with superfine tissue. The portion of
the fuselage adjacent to the wing incorporating the
fillet should be covered with the wing in place. This
will result in a neater fillet. The manner of covering is
left to the builder, for no two builders will agree as to
the correct manner. However, this might be said: The
grain of the paper should run in one direction. After
the parts have been covered a thin spray of water
should be applied to shrink the paper taut. A few
coats of banana oil will preserve the tautness of the
paper and protect it from changes in weather.
ASSEMBLY
The wing is first attached. It attaches directly
to the fuselage, with Formers #5, #6, and #7 lining up
with the center-section stringers. A piece of bamboo,
as shown on Sheet 2, is used as a fairing strip from
the wing to the fuselage. With the wing set, the center
section can now be covered with the portion of the
fuselage adjacent to the wing.
The rudder is next attached. It is glued directly
to the top stringer. To counteract torque the rudder
should be offset slightly to the left -- looking from the
cockpit.
The stabilizer is next glued in place. It is
advisable not to secure it permanently until the model
has been flown. The tail block is now glued in place
and finished off to a smooth surface.
do, weight must be added to the tail. The stabilizer
setting should be zero. With the model balanced, give
the propeller about thirty winds and hand-launch. If
the model tends to stall, increase the stabilizer angle;
if it dives, set it at a negative angle. The settings
should be slight as they will be found most effective.
The model should be fully powered to about 150
winds on four strands, somewhat less for six.
FLYING THE MODEL
The model is powered with four to six strands
of 1/8" flat rubber. The model is first glided to
determine its balance. If it stalls, weight must be
added to the cowl. If it dives, which it is likely not to
Scanned from December 1939
Air Trails
679901952.002.png
679901952.003.png
Zgłoś jeśli naruszono regulamin