easynote e.pdf
(
959 KB
)
Pobierz
Disassembly Manual
EasyNote E series
Disassembly Manual
Table of contents
Overview.................................................................................................................................................................3
Technician Notes....................................................................................................................................................3
Disassembly Instructions........................................................................................................................................3
Reassembly Instructions ........................................................................................................................................3
Required Tools .......................................................................................................................................................3
Hazardous Voltage .................................................................................................................................................4
Avoid Electrostatic Discharge.................................................................................................................................4
Power Supply Unit ..................................................................................................................................................4
Removing the Battery .............................................................................................................................................5
Removing the Hard Disk Drive ...............................................................................................................................6
Removing the Memory Module ..............................................................................................................................8
Removing the Wireless LAN ..................................................................................................................................9
Removing the CPU...............................................................................................................................................10
Removing the Optical Disk Drive..........................................................................................................................13
Removing the Keyboard .......................................................................................................................................14
Removing the Main Board....................................................................................................................................15
Removing the LCD Module ..................................................................................................................................20
Removing the LCD Panel.....................................................................................................................................21
Removing the Touch Pad.....................................................................................................................................24
Removing the Speaker Assembly ........................................................................................................................25
DIP Switch Setting................................................................................................................................................25
Screws ..................................................................................................................................................................26
Notice ...................................................................................................................................................................27
EasyNote E Series Disassembly Manual
Page 2
Overview
This document contains step-by-steps disassembly instructions for the EasyNote E series chassis. The instructions
are illustrated where necessary with images of the part that is being removed or disassembled. Furthermore, the
screws that are removed are shown next to the image of the parts themselves.
NEC reserves the right to make changes to the EasyNote E series chassis without notice.
Technician Notes
Only technicians authorized by NEC Computers International BV should attempt to repair this equipment. All
troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the
complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component
level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. Any
indication of component replacement or printed wiring board modifications may void any warranty or exchange
allowances.
Disassembly Instructions
When disassembling the system unit, follow these general rules:
n
Do not disassemble the system into parts that are smaller than those specified in the instructions.
n
Label all removed connectors. Note where the connector goes and in what position it was installed.
n
Turn off the power and disconnect all power and all options.
Reassembly Instructions
Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are returned
to their proper positions. Check that no tools or any loose parts have been left inside the chassis. Check that
everything are properly installed and tightened.
Required Tools
All disassembly procedures can be perform using the following tools:
n
PH 0x60 Philips screwdriver
n
PH 0x40 Philips screwdriver
n
4.0 x 60 Flat screwdriver
n
2.0 x 30 Flat screwdriver
n
SW5,0 Spacer screwdriver
n
Small tweezers
n
Pin
EasyNote E Series Disassembly Manual
Page 3
Hazardous Voltage
There is hazardous voltage present inside the computer
when it is connect to an AC supply, even when the
computers power switch is off. Exposure to hazardous
voltage could cause personal injury. To avoid risk of injury,
contact an Authorized Service Provider for proper
(UN)installation of optional hardware devices.
WARNING
Ensure that the computer is disconnected from
its power source and from all
telecommunications links, networks, or modem
lines whenever the chassis cover is removed.
Do not operate the computer with the cover
removed.
AVERTISSEMENT
Assurez-vous que le système est débranché de
son alimentation ainsi que de toutes les
liaisons de télécommunication, des réseaux, et
des lignes de modem avant denlever le capot.
Ne pas utiliser le système quand le capot est
enlevé.
Avoid Electrostatic Discharge
Electrostatic electricity can easily damage circuit cards and
integrated circuits (ICs). To reduce risk of damage, store
them in protective packaging whenever they are not
installed in your system.
WARNUNG
Das System darf weder an eine Stromquelle
angeschlossen sein noch eine Verbindung mit
einer Telekommunikationseinrichtung, einem
Netzwerk oder einer Modem-Leitung haben,
wenn die Gehäuseabdeckung entfernt wird.
Nehmen Sie das System nicht ohne die
Abdeckung in Betrieb.
Add-in cards can be extremely sensitive to ESD and always
require careful handling. After removing the card from the
computer, place the card flat on a grounded, static-free
surface, component-side up. Use a conductive foam pad if
available, but not the card wrapper. Do not slide the card
over any surface.
Before you install or remove memory modules, video
memory, disk drives, circuit cards or other devices, protect
them from static electricity. To do so, make sure your
computers power switch is OFF. Then, unplug the
computers AC power cord. Before picking up the device you
(un)install, you should wear an anti-static wrist wrap
(available at electronic supply stores). Be sure to connect
the wrist wrap to an unpainted metal portion of the computer
chassis. As an alternative, you can dissipate electrostatic
build-up by touching an unpainted metal portion of the
computer chassis with one hand. Then touch the device you
are (un)installing with the other hand, and maintain
continuous contact with it until it is (un)installed in the
computer.
ADVERTENCIA
Asegúrese de que cada vez que se quite la
cubierta del chasis, el sistema haya sido
desconectado de la red de alimentación y de
todos lo enlaces de telecomunicaciones, de red
y de líneas de módem. No ponga en
funcionamiento el sistema mientras la cubierta
esté quitada.
WAARSCHUWING
Zorg er voor dat alle verbindingen van en naar
de computer (stroom, modem netwerk, etc)
verbroken worden voordat de behuizing
geopend wordt. Zet de computer nooit aan als
de behuizing geopend is.
Power Supply Unit
Under no circumstances should you attempt to disassemble
the power supply. The power supply contains no user-
serviceable parts. Inside the power supply are hazardous
voltages that can cause serious personal injury. Always
return a defective power supply to your dealer.
AVVERTENZA
Prima di rimuovere il coperchio del telaio,
assicurarsi che il sistema sia scollegato
dallalimentazione, da tutti i collegamenti di
comunicazione, reti o linee di modem. Non
avviare il sistema senza aver prima messo a
posto il coperchio
EasyNote E Series Disassembly Manual
Page 4
Removing the Battery
Perform the following steps to remove the battery:
1. Make sure to power off the EasyNote E series.
2. Turn the unit upside down.
3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1
Fig. 1
Removing the battery
EasyNote E Series Disassembly Manual
Page 5
Plik z chomika:
andrzej749
Inne pliki z tego folderu:
easynote butterfly xs(1).pdf
(6544 KB)
easynote bu(1).pdf
(3210 KB)
easynote dt85(1).pdf
(37269 KB)
ipower gx(1).pdf
(42743 KB)
dot m a(1).pdf
(10641 KB)
Inne foldery tego chomika:
Acer
Apple
Asus
Benq
Clevo
Zgłoś jeśli
naruszono regulamin