rhino.pdf
(
106 KB
)
Pobierz
Rhinoceros.PDF
Black Rhinoceros
Ronald Koh - 1993
1.
2.
A sheet of paper of at least 20 cm square
would be preferred for this model. Fold and
unfold diagonally in half, creasing well.
Now fold the lower diagonal edges to meet
along the vertical crease line in the centre.
3.
4.
5.
Turn paper over ...
... and fold down the
triangular portion at the
top as illustrated.
Turn the paper over
again ...
6.
7.
... and unfold the overlapping layer to
each side ...
... like this. Now fold vertically in half,
from left to right ...
c
8.
9.
10.
... then valley fold along the
edge of the white triangular
portion, crease firmly, and
unfold.
Separate the two layers
along the horizontal edge
and squash fold.
Fold and unfold,
Creasing firmly ...
11.
12.
13.
Do a petal fold by pulling the
diagonal edge of the
uppermost layer 45 degrees
down and to the left, while
drawing in the horizontal and
vertical edges at the top
together ...
... like this. Turn the
paper over, ...
... separate the two layers
along the diagonal
edges on the left and
squash fold.
15.
16.
14.
Valley fold the horizontal edge
of the white layer to meet the
diagonal edge of the coloured
layer on each side, ...
... then fold done the
coloured triangular
portion in the middle
as illustrated.
Fold down both corners at
the top, and do a rabbit's
ear fold at the bottom ...
17.
18.
... like this. Separate the two
layers of the triangular tab
and squash fold, ...
... then mountain fold along the existing
diagonal crease lines to narrow the
upper section before bringing the point
at the top to meet the point at the
bottom ...
19.
20.
21.
... like this.
Fold the lower diagonal edges to
meet the adjacent diagonal edge
of the kite-shaped flap in the
centre, crease firmly, and unfold.
Fold and unfold again as
illustrated, creasing firmly again.
22.
23.
24.
Fold the first layer up,...
... then turn the model over.
25.
Grasp each side at the circled
areas, holding the coloured
portions only, then pull apart to
open out ...
26.
... like this. Now lift up the
the white triangular layer
at the top and the second
layer at the bottom ...
27.
... then collapse along the existing crease
lines with mountain and valley folds as
illustrated ...
... like this ...
28.
29.
30.
Draw one layer to the left and
squash fold ...
... as illustrated, then fold and
unfold, creasing firmly.
Valley fold the triangular
tabs in the middle
upwards, at the same
time valley folding the
lower diagonal edges to
meet in the centre ...
31.
32.
33.
... like this. Fold down the
triangular tabs in the
middle again.
Swivel one layer on the
right to the left.
Fold and unfold, creasing
firmly, ...
35.
34.
... then reverse fold along the
crease lines made in Step 33
...
... like so. Fold and unfold, creasing
firmly again, ...
36.
37.
... then mountain fold the excess
paper under along the crease line
made in Step 35.
Rabbit's ear fold as shown,
swivelling one layer on the left
to the right.
38.
39.
40.
Swivel one layer on
the left to the right, and
repeat from Step 33 on
this side.
Turn model
over.
Separate the two
layers along the
diagonal edges
and squash fold, ...
41.
42.
43.
44.
... then narrow as
illustrated ...
45.
... like this. Reverse fold the
corners along the
existing crease lines and
bring the resulting point
at the bottom all the way
to the top.
Fold the flap
down again ...
... and crimp with a
mountain and
valley fold, ...
... like this.
46.
47.
48.
49.
Fold down one layer
from the top ...
... then fold up
again, making a
little crimp.
Turn the model
over.
50.
Fold down the first
layer at the apex of
the model and crease
well, then reverse fold
the points on each side.
51.
Fold up the the first layer at
the apex again, and valley
fold the lower points
upwards at the illustrated
angles and proportions.
Valley fold the lower
points down again.
Plik z chomika:
wrim
Inne pliki z tego folderu:
xwing.pdf
(109 KB)
wasp.pdf
(94 KB)
vulture.pdf
(160 KB)
tyrannosaurus.pdf
(119 KB)
TOWERBOX.pdf
(81 KB)
Inne foldery tego chomika:
Sawyer Robert
Zgłoś jeśli
naruszono regulamin