Jak czytać schematy robienia na drutach.pdf

Page 1/5

What is a Chart?

A chart is a symbolic representation of your knitting, as seen from the right side of the work.

Each symbol, or group of symbols, has a definition that tells you how to knit that stitch. Here's

a very simple chart, for a k2p2 ribbing stitch:

All charts for this document were created

using The Knit Visualizer, available soon

from The Knit Foundry. Email any

questions, suggestions, corrections, etc to

info@knitfoundry.com

Reading the Chart

By looking at the Legend, we know that the empty squares represent knit stitches, and the

squares with a dot in them are purl stitches. You'll notice that the column headings in the chart

go from right to left. That's because you read the chart from right to left, just as you knit the

rightmost stitches first. In an uncharted pattern, you might see a k2p2 ribbing written as:

R1: *k2 p2 repeat from * to end of row

You start each row with a knit stitch in these instructions, or in reading from the chart. However,

the repeat indicators ("*" and "repeat from *") are implied in the chart. You could show the

repeat in the chart, but it would be a waste of space. Here is (k2 p2) 5 times:

This would be like writing:

R1: k2, p2, k2, p2, k2, p2, k2, p2, k2, p2

It's much harder to see where the actual repeat is when it's written this way. Imagine if the

middle p2 were a p3! I'd probably miss it the first time through, and then wonder why my stitch

count was off later on. In a chart, that kind of difference would be very obvious:

While this example seems a bit overdone, it is meant to demonstrate how the visual aspect of

charts can really help you see what you need to knit.

Charts for Flat Knitting vs. Circular Knitting

So far we know to look at the chart's Legend to see what each symbol means, read the chart

starting from the right, and moving to the left, just like our stitches do on our needles. This

works when we are looking at the right side of the knitting. What happens when we reach the

end of the row, and turn it over? We're now facing the back of the work! We can't simply start

over at the right side of the chart, our knitting would end up looking wrong. In that case, we

need to know what those symbols mean when we are looking at the wrong side. Our legend can

tell us that information.

www.knitfoundry.com

Page 2/5

This is the same exact chart as shown above, but with additional information included in the

legend. The legend tells us to knit empty squares on the right side (RS), but purl them when on

the wrong side (WS). The last thing we need to know about reading a chart when working on a

wrong side row is to read the chart from the left now. The chart represents the view of the work

from the right side, so we need to imagine that we've flipped the chart around and we're looking

at it from the backside. If the chart had more than one row in it, the row number location

would give us a hint on which way to read each line. Here is the chart for Mistake Stitch Rib, knit

flat:

This pattern has two lines. The first line is a right side row & we start reading where the #1 is,

on the right side. The second row is a wrong side row, and we see the number 2 on the left.

This gives us a hint to read that line from that direction.

What if we are knitting our item in the round, such as in a sock? The same Mistake Stitch Rib

chart, but row numbers now indicate we're doing circular knitting:

Whatever pattern you're reading should explicitly state you are knitting in the round, but here

again the chart can give us a visual clue. All the row numbers are on the right side of the chart.

For every single row, we'll read the chart from right to left now.

Starting with a Wrong Side Row

What if the first row of your pattern isn't a right side row, but a wrong side row? The pattern

should also say which type of row to start with, but the chart can give us more clues by putting

the first row on the left side, which means to start on the wrong side of the work.

In this chart we begin on a wrong side row with row #1, and row #2 is our first right side row.

www.knitfoundry.com

Page 3/5

Reading Charts Summary

Each symbol has a meaning

For Right Side Rows, begin reading row on the Right

For Wrong Side Rows, begin reading row on the Left and use the instructions for

working that symbol from the Wrong side (WS in Legend)

In Circular patterns every row is read in the same direction, usually from the right

Charts typically only show one complete repeat which is used according to pattern

directions

Other Examples

Obviously there is more to knitting than just knit and purl stitches. Let's look at some other

commonly known patterns, and the charts.

Seed Stitch

Moss Stitch

Ripple Stitch

Barbara Walker, A

Treasury of Knitting

Patterns, p13

www.knitfoundry.com

Page 4/5

Double Cables

Rows That Are Not the Same Length

Sometimes you'll run across a chart where increases will happen on one row, and decreases will

happen on another row (common with lace or very dense cables). This leaves you with a

different number of stitches per row. To represent this in a chart, we introduce the concept of

"No Stitch". It's a symbol that specifically means "Do nothing, do not consume a stitch, just

ignore this, it's a place holder".

In the chart above, "Fan Shell", a variation on "Feather and Fan", the decreases happen on

different rows than the increases. Row three is the first row of decreases, where two decreases

happen, removing 2 stitches. As you can see, as you progress from row 3 to 4 to 5 stitches

www.knitfoundry.com

Page 5/5

slowly disappear from the edges of the chart. "No Stitch" is represented with a grey box. On the

row with the yarn overs, all the stitches are back Î so we're back up to 19 stitches. When

knitting a pattern like this, you would always start at the farthest left or right edge, ignoring the

"No Stitch" cells.

Some patterns have a "No Stitch" cell in the center, this allow you to see how the pattern lines

up in the chart; making it easier to recognize which row you are currently on.

Leaving Wrong Side Rows off the Chart

In some lace patterns, the wrong side row is always the same (either all knit or all purl stitches).

Rather than waste a lot of space in the chart, the pattern will tell you :"All even rows, knit all

stitches" and not include those rows in the chart. Here is one that creates a mock cable using

lace:

Notice the row numbers start at 1, 3, 5, etc.

Looking at Multiple Repeats of the Same Pattern (also know as "playing around")

Sometimes it's hard to see how the pattern will knit based on only a single repeat of the stitch

pattern. If you're playing around with your own charts, you might want to see what multiple

repeats look like together, and mark the single repeat. Here's Mistake Stitch Rib with two repeats

wide by three repeats tall:

The black border shows where the single repeat is. If you have ever seen Mistake Stitch Rib in

yarn, you know that you get a very strong vertical line with a row of knits (columns 5 and 1) and

a recessed area with a row of purls (Columns 3 and 7).

www.knitfoundry.com

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: