1187.PDF
(
305 KB
)
Pobierz
19-0160; Rev 2; 4/97
Dual-Output Power-Supply
Controller for Notebook Computers
__________________General Description
The MAX786 is a system-engineered power-supply
controller for notebook computers or similar battery-
powered equipment. It provides two high-performance
step-down (buck) pulse-width modulators (PWMs)
for +3.3V and +5V. Other features include dual,
low-dropout, micropower linear regulators for
CMOS/RTC back-up, and two precision low-battery-
detection comparators.
High efficiency (95% at 2A; greater than 80% at loads
from 5mA to 3A) is achieved through synchronous recti-
fication and PWM operation at heavy loads, and
Idle Mode
TM
operation at light loads. The MAX786 uses
physically small components, thanks to high operating
frequencies (300kHz/200kHz) and a new current-mode
PWM architecture that allows for output filter capacitors
as small as 30µF per ampere of load. Line- and load-
transient responses are terrific, with a high 60kHz unity-
gain crossover frequency allowing output transients to
be corrected within four or five clock cycles. Low sys-
tem cost is achieved through a high level of integration
and the use of low-cost, external N-channel MOSFETs.
Other features include low-noise, fixed-frequency PWM
operation at moderate to heavy loads, and a synchro-
nizable oscillator for noise-sensitive applications such
as electromagnetic pen-based systems and communi-
cating computers. The MAX786 is a monolithic,
BiCMOS IC available in fine-pitch, surface-mount
SSOP packages.
___________________________Applications
Notebook Computers
Portable Data Terminals
Communicating Computers
Pen-Entry Systems
________________________________Features
©
Dual PWM Buck Controllers (+3.3V and +5V)
©
Two Precision Comparators or Level Translators
©
95% Efficiency
©
420µA Quiescent Current, 70µA in Standby
(linear regulators alive)
©
25µA Shutdown Current (+5V linear alive)
©
5.5V to 30V Input Range
©
Small SSOP Package
©
Fixed Output Voltages:
3.3V (standard)
3.45V (High-Speed Pentium™)
3.6V (PowerPC™)
_________________Ordering Information
PART
TEMP. RANGE
PIN-PACKAGE
V
OUT
MAX786CAI
0°C to +70°C
28 SSOP
3.3V
MAX786RCAI
0°C to +70°C
28 SSOP
3.45V
Ordering Information continued at end of data sheet.
_____________________Pin Configuration
TOP VIEW
CS3
FB3
1
28
27
SS3
DH3
2
3
ON3
LX3
BST3
26
25
24
D1
4
5
MAX786
D2
DL3
V+
VH
6
7
23
22
Q2
VL
FB5
________Typical Application Diagram
Q1
8
21
GND
PGND
9
10
11
20
19
18
+3.3V
REF
DL5
BST5
m
P
MEMORY
PERIPHERALS
5.5V
TO
30V
POWER
SECTION
SYNC
+5V
MAX786
SHDN
12
17
LX5
SHUTD
OWN
13
ON5
16
15
DH5
CS5
POWER-GOOD
5V ON/
OFF
3.3V ON/OFF
SYNC
SS5
14
LOW-BATTERY WARNING
SUSPEND POWER
SSOP
Idle Mode is a trademark of Maxim Integrated Products. Pentium is a trademark of Intel Corp. PowerPC is a trademark of IBM Corp.
_______________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
Dual-Output Power-Supply
Controller for Notebook Computers
ABSOLUTE MAXIMUM RATINGS
V+ to GND................................................................-0.3V to 36V
PGND to GND .......................................................................±2V
VL to GND ..................................................................-0.3V to 7V
BST3, BST5 to GND .................................................-0.3V to 36V
LX3 to BST3 ...............................................................-7V to 0.3V
LX5 to BST5 ...............................................................-7V to 0.3V
Inputs/Outp
uts to
GND
(D1, D2, SHDN, ON5, REF, SS5, CS5,
FB5, SYNC, CS3,FB3, SS3, ON3) ............-0.3V to (VL + 0.3V)
VH to GND ...............................................................-0.3V to 20V
Q1, Q2 to GND ............................................-0.3V to (VH + 0.3V)
DL3, DL5 to PGND .......................................-0.3V to (VL + 0.3V)
DH3 to LX3 ..............................................-0.3V to (BST3 + 0.3V)
DH5 to LX5 ..............................................-0.3V to (BST5 + 0.3V)
REF, VL Short to GND................................................Momentary
REF Current ........................................................................20mA
VL Current ..........................................................................50mA
Continuous Power Dissipation (T
A
= +70°C)
SSOP (derate 9.52mW/°C above +70°C) ....................762mW
Operating Temperature Ranges
MAX786CAI/MAX786_CAI .................................0°C to +70°C
MAX786EAI/MAX786_EAI ...............................-40°C to +85°C
Lead Temperature (soldering, 10sec) ............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTIC
S
(V+ = 15V, GND = PGND = 0V, I
VL
= I
REF
= 0mA, SHDN = ON3 = ON5 = 5V, other digital input levels are 0V or +5V,
T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
3.3V AND 5V STEP-DOWN CONTROLLERS
Input Supply Range
5.5
30
V
0mV < (CS5-FB5) < 70mV, 6V < V + < 30V
(includes load and line regulation)
FB5 Output Voltage
4.80
5.08
5.20
V
MAX786
3.17
3.35
3.46
0mV < (CS3-FB3) < 70mV, 6V < V + < 30V
(includes load and line regulation)
FB3 Output Voltage
MAX786R
3.32
3.50
3.60
V
MAX786S
3.46
3.65
3.75
Load Regulation
Either controller (CS_ -FB_ = 0mV to 70mV)
2.5
%
Line Regulation
Either controller (V+ = 6V to 30V)
0.03
%/V
Current-Limit Voltage
CS3-FB3 or CS5-FB5
80
100
120
mV
SS3/SS5 Source Current
2.5
4.0
6.5
µA
SS3/SS5 Fault Sink Current
2
mA
INTERNAL REGULATOR AND REFERENCE
VL Output Voltage
ON5 = ON3 = 0V, 5.5V < V+ < 30V, 0mA < I
L
< 25mA
4.5
5.5
V
VL Fault Lockout Voltage
Falling edge, hysteresis = 1%
3.6
4.2
V
VL/FB5 Switchover Voltage
Rising edge of FB5, hysteresis = 1%
No external load (Note 1)
4.2
4.7
V
REF Output Voltage
3.24
3.36
V
REF Fault Lockout Voltage
Falling edge
2.4
3.2
V
REF Load Regulation
0mA < I
L
< 5mA (Note 2)
30
75
mV
S
—
H
—
D
—
–
= D1 = D2 = ON3 = ON5 = 0V, V+ = 30V
V+ Shutdown Current
25
40
µA
V+ Standby Current
D1 = D2 = ON3 = ON5 = 0V, V+ = 30V
70
120
µA
Quiescent Power Consumption
(both PWM controllers on)
D1 = D2 = 0V, FB5 = CS5 = 5.25V,
FB3 = CS3 = 3.5V
5.5
8.6
mW
V+ Off Current
FB5 = CS5 = 5.25V, VL switched over to FB5
30
60
µA
COMPARATORS
D1, D2 Trip Voltage
Falling edge, hysteresis = 1%
1.61
1.69
V
D1, D2 Input Current
D1 = D2 = 0V, 5V
±100
nA
2
________________________________________________________________________________________________
Dual-Output Power-Supply
Controller for Notebook Computers
ELECTRICAL CHARACTERISTIC
S (co
ntinued)
(V+ = 15V, GND = PGND = 0V, I
VL
= I
REF
= 0mA, SHDN = ON3 = ON5 = 5V, other digital input levels are 0V or +5V,
T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Q1, Q2 Source Current
VH = 15V, V
OUT
= 2.5V
12
20
30
µA
Q1, Q2 Sink Current
VH = 15V, V
OUT
= 2.5V
200
500
1000
µA
Q1, Q2 Output High Voltage
I
SOURCE
= 5µA, VH = 3V
VH -0.5
V
Q1, Q2 Output Low Voltage
I
SINK
= 20µA, VH = 3V
0.4
V
Quiescent VH Current
VH = 18V, D1 = D2 = 5V, no external load
4
10
µA
OSCILLATOR AND INPUTS/OUTPUTS
SYNC = 3.3V
270
300
330
Oscillator Frequency
kHz
SYNC = 0V, 5V
170
200
230
SYNC High Pulse Width
200
ns
SYNC Low Pulse Width
200
ns
SYNC Rise/Fall Time
Not tested
200
ns
Oscillator SYNC Range
240
350
kHz
SYNC = 3.3V
89
92
Maximum Duty Cycle
%
SYNC
= 0V or 5V
92
95
Input Low Voltage
SHDN
, ON3, ON5, SYNC
0.8
V
SHDN, ON3, ON5
2.4
Input High Voltage
V
SYNC
VL -0.5
Input Current
SHDN, ON3, ON5 V
IN
= 0V, 5V
±1
µA
DL3/DL5 Sink/Source Current
V
OUT
= 2V
1
A
DH3/DH5 Sink/Source Current
BST3-LX3 = BST5-LX5 = 4.5V, V
OUT
= 2V
1
A
DL3/DL5 On-Resistance
High or low
7
½
DH3/DH5 On-Resistance
High or low, BST3-LX3 = BST5-LX5 = 4.5V
7
½
Note 1:
Since the reference uses VL as its supply, its V+ line regulation error is insignificant.
Note 2:
The main switching outputs track the reference voltage. Loading the reference reduces the main outputs slightly according
to the closed-loop gain (AV
CL
) and the reference voltage load-regulation error. AV
CL
for the +3.3V supply is unity gain.
AV
CL
for the +5V supply is 1.54.
_________________________________________________________________________________________________
3
Dual-Output Power-Supply
Controller for Notebook Computers
________________________________________________Typical Operating Characteristics
(Circuit of Figure 1, T
A
= +25°C, unless otherwise noted.)
EFFICIENCY vs. +5V OUTPUT
CURRENT, 200kHz
EFFICIENCY vs. +5V OUTPUT
CURRENT, 300kHz
EFFICIENCY vs. +3.3V OUTPUT
CURRENT, 200kHz
100
100
100
V
IN
= 15V
V
IN
= 6V
90
90
90
V
IN
= 6V
V
IN
= 6V
V
IN
= 15V
V
IN
= 15V
V
IN
=
30V
80
80
80
V
IN
= 30V
V
IN
= 30V
70
70
70
+3.3V OFF
SYNC = 0V, +3.3V OFF
60
60
SYNC = 0V, +5V ON
60
50
50
50
1m
10m
100m
1
10
1m
10m
100m
1
10
1m
10m
100m
1
10
+5V OUTPUT CURRENT (A)
+5V OUTPUT CURRENT (A)
+3.3V OUTPUT CURRENT (A)
QUIESCENT SUPPLY CURRENT vs.
SUPPLY VOLTAGE
STANDBY SUPPLY CURRENT vs.
SUPPLY VOLTAGE
EFFICIENCY vs. +3.3V OUTPUT
CURRENT, 300kHz
100
19
2.5
V
IN
= 15V
90
2.0
18
V
IN
= 6V
ON3 = ON5 = HIGH
80
1.5
V
IN
= 30V
2
ON3 = ON5 = 0V
70
1.0
+5V ON
1
0.5
60
0
50
0
1m
10m
100m
1
10
0
6
12
18
24
30
0
6
12
18
24
30
SUPPLY VOLTAGE (V)
+3.3V OUTPUT CURRENT (A)
SUPPLY VOLTAGE (V)
MINIMUM V
IN
TO V
OUT
DIFFERENTIAL
vs. +5V OUTPUT CURRENT
SHUTDOWN SUPPLY CURRENT vs.
SUPPLY VOLTAGE
SWITCHING FREQUENCY vs.
LOAD CURRENT
1000
1.0
500
SYNC = REF (300kHz)
ON3 = ON5 = 5V
0.8
400
100
300kHz
+5V, V
IN
= 7.5V
300
0.6
10
SHDN = 0V
+5V, V
IN
= 30V
200
200kHz
0.4
+3.3V, V
IN
= 7.5V
1
+5V OUTPUT
STILL REGULATING
0.2
100
0.1
100
m
0
0
1m
10m
100m
1
10
1m
10m
100m
1
0
6
12
18
24
30
LOAD CURRENT (A)
+5V OUTPUT CURRENT (A)
SUPPLY VOLTAGE (V)
4
_______________________________________________________________________________________
Dual-Output Power-Supply
Controller for Notebook Computers
_________________________________Typical Operating Characteristics (continued)
(Circuit of Figure 1, T
A
= +25°C, unless otherwise noted.)
IDLE MODE WAVEFORMS
PULSE-WIDTH MODULATION MODE WAVEFORMS
+5V OUTPUT
50mV/div
LX 10V/div
2V/div
+5V OUTPUT
50mV/div
500ns/div
+5V OUTPUT CURRENT = 1A
V
IN
= 16V
200
m
s/div
I
LOAD
= 100mA
V
IN
= 10V
+5V LOAD-TRANSIENT RESPONSE
+3.3V LOAD-TRANSIENT RESPONSE
3A
0A
3A
0A
LOAD CURRENT
LOAD CURRENT
+5V OUTPUT
50mV/div
+3.3V OUTPUT
50mV/div
200
s/div
V
IN
= 15V
m
200
m
s/div
V
IN
= 15V
_______________________________________________________________________________________
5
Plik z chomika:
Kot_Maciek
Inne pliki z tego folderu:
0001.PDF
(10 KB)
1003.PDF
(374 KB)
1002.PDF
(139 KB)
1004.PDF
(342 KB)
1005.PDF
(170 KB)
Inne foldery tego chomika:
PDF2
PDF3
SPICE
Zgłoś jeśli
naruszono regulamin