CP243-1_Excel.pdf

(1019 KB) Pobierz
14759477 UNPDF
SIMATIC NET
Step by Step:
Excel OPC-Automation Client
for access to S7-200 with
CP243-1
Overview and
1
Handbuch
Manual
2
3
4
Ausgabe 02/2003
Step by Step:
Excel OPC-Automation Client for access to S7-200 with CP243-1
1
14759477.001.png
Classification of Safety-Related Notices
This document contains notices which you should observe to ensure your own
personal safety, as well as to protect the product and connected equipment. These
notices are highlighted in the manual by a warning triangle and are marked as follows
according to the level of danger:
!
Danger
indicates that death or severe personal injury will result if proper precautions are not
taken.
!
Warning
indicates that death or severe personal injury can result if proper precautions are not
taken.
!
Caution
with warning triangle indicates that minor personal injury can result if proper
precautions are not taken.
Caution
without warning triangle indicates that damage to property can result if proper
precautions are not taken.
Notice
indicates that an undesirable result or status can result if the relevant notice is
ignored.
Note
highlights important information on the product, using the product, or part of the
documentation that is of particular importance and that will be of benefit to the user.
Copyright Siemens AG, 1998 to 2003, All rights reserved
The reproduction, transmission or use of this document or its contents is
not permitted without express written authority. Offenders will be liable for
damages. All rights, including rights created by patent grant or registration
of a utility or design, are reserved.
Disclaimer
We have checked the contents of this manual for agreement with the
hardware described. Since deviations cannot be precluded entirely, we
cannot guarantee full agreement. However, the data in this manual are
reviewed regularly and any necessary corrections included in subsequent
editions. Suggestions for improvement are welcomed.
Siemens AG
Bereich Automatisierungs- und Antriebstechnik
Geschäftsgebiet Industrie-Automatisierungssysteme
Postfach 48 48, D-90327 Nürnberg
© Siemens AG 1998 to 2003
Technical data subject to change.
Siemens Aktiengesellschaft
Printed in the Federal Republic of Germany
2
14759477.002.png
Trademarks
and SIMATIC NET Networking for Industry ®
are registered trademarks of Siemens AG.
, SIMATIC NET
, SINEC
Third parties using for their own purposes any other names in this document which
refer to trademarks might infringe upon the rights of the trademark owners.
Safety Instructions Regarding your Product
Before you use the product described here, read the safety instructions below
thoroughly.
Qualified Personnel
Only qualified personnel should be allowed to install and work on this equipment.
Qualified persons are defined as persons who are authorized to commission, to
ground, and to tag circuits, equipment, and systems in accordance with established
safety practices and standards.
Correct Usage of Hardware Products
Please note the following instructions regarding the correct usage of hardware
products:
Caution
This device and its components may only be used for the applications described in the
catalog or the technical description, and only in connection with devices or
components from other manufacturers which have been approved or recommended
by Siemens.
This product can only function correctly and safely if it is transported, stored, set up,
and installed correctly, and operated and maintained as recommended.
Before you use the supplied sample programs or programs you have written yourself,
make certain that no injury to persons nor damage to equipment can result in your
plant or process.
EU Directive: Do not start up until you have established that the machine on which
you intend to run this component complies with the directive 89/392/EEC
Step by Step:
Excel OPC-Automation Client for access to S7-200 with CP243-1
3
SIMATIC
14759477.003.png
Correct Usage of Software Products
Please note the following instructions regarding the correct usage of software
products:
Caution
This software may only be used for the applications described in the catalog or the
technical description, and only in connection with software products, devices, or
components from other manufacturers which have been approved or recommended
by Siemens.
Before you use the supplied sample programs or programs you have written yourself,
make certain that no injury to persons nor damage to equipment can result in your
plant or process.
Prior to Startup
Prior to startup, please note the following warning:
Caution
Prior to startup you must observe the notes in the relevant documentation. For
ordering data of the documentation please refer to catalogs or contact your local
SIEMENS representative.
Step by Step:
Excel OPC-Automation Client for access to S7-200 with CP243-1
4
14759477.004.png
Preface
Preface
Purpose of the Manual
This manual supports you when creating user programs and configurations in the
OPC environment. The activities involved in creating a program and the required
configuration work are presented in the form of a sequential series of steps. The
configurations used are created with the basic software SIMATIC STEP 7 or NCM
PC.
This manual serves as a reference work for configuration and communication with
OPC components.
Aims
This manual should help you to expand the components described and to integrate
them in your program.
We assume that you are thoroughly familiar with your programs and development
environment.
The Package
This sample project consists of the following parts:
● Documentation commissioning, documentation Excel
● Microsoft Excel file incl. VBA implementation as example
● MicroWIN project file for download
● SimaticNet OPC project file for observing variables
Validity of this Manual
This manual applies the following software versions:
Step by Step:
Excel OPC-Automation Client for access to S7-200 with CP243-1
5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin