Kody serwisowe Kody bledw podstawowe operacje.pdf

Technical Information for XD-100 style

Strona 1 z 7

XD-100 style

(XD100/102/103/104/105, X120/122, ,XD155 )

TECHNICAL INFORMATION

All model #'s are trademarks of Xerox § Corporation

STATUS CODES:

A1/A2 SDF Document Jam

CH Toner Cartridge not present or not seated properly

C1 Right Side Door Open

E2 Paper Jam

E7-01 GDI Memory Board error (Graphical User Interface)

E7-03 Laser Output Error. Make sure the Right Side Door is closed securely...try turning machine off and back on to

see if the fault will clear.

E7-04 CCD ('Charge Coupled Device' or 'photoelectric converter) white level error

E7-05 CCD black level error

E7-12 CCD shading level error

E7-14 ASIC communication error (try clearing by turning off and on...otherwise Main PWB is bad)

E7-15 Copy Lamp Problem

H2 Thermistor Open

H3* High fuser temperature

H4* Low fuser temperature

J1 Toner Cartridge empty

J2 Drum Cartridge end of life

L1 Scanner carriage did not leave home position on power up or upon pressing start

L3 Scanner carriage did not return to home position after copy cycle

L4 Main motor problem

L6 Polygon motor (drives the laser) problem

P Paper feed problem (Paper didn't reach the paper feed sensor in time)

U2** Memory failure

DIAGNOSTICS:

To enter diagnostic : Turn on the power and within 4 seconds press the following sequence: 'Clear', 'Exposure Mode', 'Clear',

'Exposure Mode' (Exposure Mode is the button on the far left). The console will go completely blank.

To enter a code : Select the first part of the code using the copy quantity buttons, followed by the 'Print' button, then the second part of

the code followed by the 'Print' button again.

To exit diagnostics : Press 'Clear' repeatedly or turn the power off.

*To clear a fuser code :(14) Enter diagnostics, select '14' followed by 'Print'... exit diagnostics.

**To Clear a U2 code :(16) Enter diagnostics, select '16' followed by 'Print' ... exit diagnostics.

Testing Switches & Sensors : (Input Component Codes)

In diagnostic mode, enter the code for the component, press 'Print', then manually actuate the switch or sensor and watch for the

Corresponding Lamp to turn on & off.

file://\\Serwer\Serwice%20Manuals\Xerox\pages\XD100inf.html

2004-12-21

Technical Information for XD-100 style

Strona 2 z 7

Code Component

Control Console Lamp to watch

1-2

Scan Home Sensor

Drum Cartridge Lamp

2-2

Set Detect Sensor

Toner Cartridge Lamp

2-2

Docmunet Path Sensor

Paper Jam Lamp

2-2

Doc Cover Closed Sensor

Drum Cartridge Lamp

2-2

Document Position Sensor

SDF Jam Lamp

30-1

Paper Feed Sensor

Toner Cartridge Lamp

30-1

Fuse Jam Sensor

Paper Jam Lamp

30-1

Paper Exit Sensor

Drum Cartridge Lamp

30-1

Drum Rest Sensor

R/E Lamp

Checking Clutches, Motors, Lamps, Solenoids & Corotrons: (Output Component Codes)

Use these codes to test a component such as a clutch or motor. Enter the code followed by ' Print ' to activate a component. Most

components activate for 1 second (Exposure lamp lights for 5)

Code Component

1-1

Scan Drive Motor

- The first time 'Print' is pressed, optics move into home position...

Then select the magnification you want to observe... the second

time 'Print' is pressed, optics scan at the speed corresponding to

the magnification selected.

- The Drum Cartridge Lamp should light whenever the scanner

reaches the home position.

2-3

SDF Motor

- SDF Motor rotates for 10 seconds at a speed corresponding to

the selected magnification.

2-4

Document Feed Solenoid

- Solenoid cycles 20 times when 'Print' is pressed.

2-5

Document Exit Pinch Roll Solenoid

- Exit Pinch Roll Solenoid cycles 20 times when 'Print' is pressed.

2-6

Document Exit Roll Clutch

- Exit Roll Clutch cycles 20 times when 'Print' is pressed.

2-7

Document Deflection Gate Solenoid

- Deflection Gate Solenoid cycles 20 times when 'Print' is pressed.

5-1

Control Panel Lamps

- Control console lamps light for 5 seconds each time 'Print' is

pressed.

5-2

Fuser Lamp & Fuser Exhaust Fan

- Press 'Print', lamp pulses on 5 times & Exhaust Fan will run in

high speed mode.

file://\\Serwer\Serwice%20Manuals\Xerox\pages\XD100inf.html

2004-12-21

Technical Information for XD-100 style

Strona 3 z 7

5-3

Exposure Lamp

- Lamp lights for 5 seconds each time 'Print' is pressed.

6-1

Paper Feed Solenoid

- Paper feed solenoid for the selected tray cycles 20 times when

'Print' is pressed.

6-2

Registration Roller Solenoid

- Registration solenoid cycles 20 times when 'Print' is pressed.

8-6

Transfer Corotron Voltage

- Transfer Corotron output is present for 30 seconds each time

'Print' is pressed.

Note: This measurement is made at the Transfer Corotron Plate

with the Side Door open and the Side Door Interlock acuated.

Voltage=1200 Volts DC (not under load)

Toner Motor

- When 'Print' is pressed, motor runs for 30 sec.

25-10

Polygon Motor

- When 'Print' is pressed, motor runs for 30 sec.

64-1

Print Engine

- Produces a solid grey test print when 'Print' is pressed.

Checking Counters

Checking the Total Copy Count :(22-5) Enter diagnostics, select '22', 'Print' followed by '5', 'Print'...The copy count will flash 3 digits

at a time for a total of six digits (for example: 012 345 would indicate 12,345 copies).

(Can also be done by the customer by holding the 'Clear' button for 7 seconds)

Checking the Drum Cartridge (CRU) Count :(22-12) Enter diagnostics, select '22', 'Print', followed by '12', 'Print'...The copy count

will flash 3 digits at a time for a total of six digits (for example: 002 345 would indicate 2,345 copies).

Drum Count Reset :(24-7) Enter diagnostics, select '24', 'Print', followed by '7','Print', followed by 'Print' again. This resets the drum

count to zero.

Adjusting the Developer Bias:

( WARNING: Unplug the machine before you hook up meter leads on the Power Supply PWB).

Set your meter to 4000 VDC. Connect the '+' side of your meter to CN10, Pin 1 (CN10-1)... connect the '-' lead to CN10, pin 2 (CN10-

2). Enter diagnostics. With the Toner Cartridge installed, select Code 25-1...When 'Print' is pressed, the Main Motor will run and the

Developer Bias will be present for 30 seconds. Adjust by turning VR121 (also on the Power Supply PWB), look for a voltage of -

380VDC +/-15VDC.

Adjusting the Grid Bias: (-3 & 8 -2)

( WARNING: Unplug the machine before you hook up meter leads on the Power Supply PWB).

Set your meter to 4000VDC. Connect '+' to CN11, Pin 3 (CN11-3) on the Power Supply PWB, and '-' to the chassis. Enter diagnostics.

You'll want to adjust for the "Low" Mode first....

Select Code 8-3...When 'Print' is pressed, the Grid Bias (for 'Low' mode) will be present for 30 seconds. Adjust VR141 on the Power

Supply PWB for a voltage of -420VDC +/-20VDC,

Select Code 8-2...When 'Print' is pressed, the Grid Bias (for 'High' mode) will be present for 30 seconds. Adjust VR142 on the Power

Supply PWB for a voltage of -580VDC +/-20VDC,

Side Edge Erase: (XD-120)(26-43)

Enter diagnostics... Enter '26', 'Print'...'43', 'Print'... the current setting will be displayed.

Range is 0 to 10 with .5mm increments. (0=0mm, 10=5.0mm) 4 is the default (2.0mm). To change the setting, press the Copy Quantity

Select 'ones' button till you get what you want, then press 'Print'.

Fuser Temperature Adjustment: (43-1)

Enter diagnostics... Enter '43','Print'...'1','Print'... the current setting will be displayed.

0=175 (default)... 1=180c...2=185c...3=190c...4=195c...5=200c. Default is 3 (190c) for all models except the XD155 which has 4

(195c) as it's default.If you want to change the setting, use the copy quantity button & press 'Print' to lock in your selection.

file://\\Serwer\Serwice%20Manuals\Xerox\pages\XD100inf.html

2004-12-21

Technical Information for XD-100 style

Strona 4 z 7

Fuser Temperature Adjustment for Multiple Copy Runs: (43-4)

After 20 copies, the machine is designed to lower the fusing temperature to a preset value.

Enter diagnostics... Enter '43','Print'...'2','Print'... the current setting is displayed.

0=155...1=160...2=165...3=170...4=175...5=180. Default is 2(165c) for all models except the XD155 which has 3 (170c) as it's default.

Change using the copy quantity select button & press 'Print' to lock in your selection.

Exposure Adjustment: (46-1...for SDF=51-6)

Should be done after replacing Exposure lamp, Exposure Sensor, Exposure PWB, or Main PWB

First clean all optics & align the 'Exposure Plates' on the Exposure Lamp Carriage so that the copy is evenly exposed.

Then select '46','Print','1','Print'....Place a Test Pattern on the glass, select the copy mode (Auto, Test, Photo, or Toner Save)

you wish to adjust...Press 'Print' to run a copy. The current exposure level is displayed. Increase the number shown (range is

from 00 to 99, Default is 50) to increase exposure (lighter copy). Decrease the number shown to darken the copy.

For SDF Exposure adjustment , follow same procedure but use the diagnostic code '51', 'Print', '6', 'Print' instead of the 46-1

shown above.

Magnification Adjustments :(48-1) Ranges are from 00 to 99, Default=50.

'Front to Rear ' magnification: (adjusts the position of the lens)

Automatic Adjustment Enter diagnostics, select '48', 'Print', '1', 'Print'. Press the 'Exposure Mode' button until only the 'Auto'

lamp is lit, then press 'Print'...the machine will scan the reference line on the calibration strip, calculate the "correct"

magnification & automatically adjust the setting...the new setting appears in the display.

Manual Adjustment: To manually adjust the setting, enter '48', 'Print', and then press the 'Exposure Mode' button until only the

'Text lamp is lit....the current setting is displayed (Range is 00-99, Default=50). Adjust up to increase the magnification, down

to decrease. Press 'Clear' to Exit diagnostics & store new settings.

Lead Edge to Trail Edge: magnification: (adjusts the scan speed)

Same procedure as for 'Front to Rear' but press 'Exposure Mode' button until only the 'Photo' lamp is lit.

Registration & Deletion Adjustments :(50-1) Ranges are 00 to 99, Default=50

Lead Edge Registration :(changes the timing of the sheet) Enter diagnostic code '50', 'Print', '1', 'Print'... press 'Exposure Mode'

button until 'Auto' lamp is lit... Increase number shown to decrease the distance between the lead edge & the image. Each 1

step increment produces a shift of 01.mm

SDF Lead Edge Registration : Same as above but press 'Exposure Mode' button until 'Auto' & 'Text' lamps are lit to make your

changes.

Lead Edge Deletion: Same as above but press 'Exposure' and 'Copy Contrast' buttons until only the 'Auto' lamp is lit. Adjust

number up to increase deletion, down to decrease.

Trail Edge Deletion: Enter diagnostic code 50-1... press 'Exposure Mode' until the 'Auto', 'Text', &'Photo' lamps are lit....adjust

number shown up to increase, down to decrease.

Front to Rear Registration (Center Offset) Adjustments : (50-10) Ranges are 00 to 99, Default=50

Paper Tray 1 & 2 : Enter '50', 'Print', '10', 'Print'. Use the 'Exposure Mode' button to select 'Auto' & the 'Paper Tray Select'

button to choose 'Paper Tray 1', the current value is displayed... To shift the image toward the front of the machine, increase

the number... to move towards the rear, decrease. A change of 1 produces a 0.1mm shift. Do the same with the 'Paper Tray 2'

selected to change that setting seperately.

Bypass : Same idea, but select 'Auto' only (for machines with single sheet bypass only), or 'Auto' & 'Alternate Tray'

lamps...that value is displayed, make your change.

Registration Buckle: (51-2) Ranges from 00 to 99È Default=50

Paper Tray Registration Buckle: Enter diagnostics, select '51', 'Print', '2', 'Print'... press the 'Exposure' button until only the

'Auto' lamp and the paper tray you want to change the setting for is lit. Use copy quantity buttons to change.

Alternate Tray Registration Buckle : same as above but press the 'Exposur' button until only the 'Auto' & 'Alternate Tray'

lamps are lit... for machines with Single Sheet Bypass, select 'Auto' only.

Configuration Codes : to display & change various machine configurations... to change, select new number with copy quantity

buttons, then press 'Print'

Code: Function:

Range: Default: Details:

26-1

Tray Configuration

0 or 1

0 = Single Sheet Bypass

1 = Alternate Tray

file://\\Serwer\Serwice%20Manuals\Xerox\pages\XD100inf.html

2004-12-21

Technical Information for XD-100 style

Strona 5 z 7

26-2

SDF Configuration

0 or 1

0 = Without SDF

1 = With SDF

26-3

2 nd Tray Setting

(XC 1250/1255 Only)

0 or 1

0 = 1 Tray

1 = 2 Tray

26-4

Duplex Setting

(XC 1250/1255 Only)

0 or 1

0 = Without Duplex

1 = With Duplex

26-6

Paper Size Type

0,1,or 2

0 = Inch Series

1 = AB Series

2 = Japan AB Series

26-7

Copies per Minute

(Read only, cannot

be changed from

this code).

10,12,15

10CPM='10'displayed

12CPM='12' displayed

15CPM='15' displayed

26-20

Trail Edge Deletion

0 or 1

0=Trail Deletion allowed

1=Not allowed

26-30

CE mark application

0 or 1

0=CE mark application control off

1=CE mark application control on

26-38

Drum Cartridge Life End

0 or 1

0=End of Life disabled

1=End of Life Enabled

26-39

Memory Capacity

0,1 or 2

0=No memory

1=4Mbyte

2=6Mbyte

26-40

Polygon motor Off time setting 0,1,2 or 3

0=0 seconds

1=30 seconds

2=60 seconds

SPECIFICATIONS:

Manufacturer: Sharp ° Corporation also sold as Z-835 & similar model #Ós.

Copies/Minute: 100/102/103/104/105 are set up for 10CPM

120/122 are set for 12CPM

155 set for 15CPM

Print Rate: 8 prints per minute (600 dpi)

Suggested Retail Price: Ranges from $600. - for XD100 to $1900.- for XD155df

Zoom Capabilities: 50-200% Presets = 50,64,78,100,129,200, +1 customer settable

Paper Sizes:

Copy Paper from Paper Tray 1 or 2: (16-24 lb.) 8.5x5.5" To 8.5x14"

Copy Paper from Bypass (14-34 lb.) 3.5x5.5" To 8.5x14"

SDF Document Paper: (16-24 lb.) 5.5x8.5" To 8.5x14"

First Copy Time: 9 seconds (warm)... 23 seconds (cold)... Warm up Time: 23 seconds.

Yields:

Drum Cartridge: 12,000 (gives a 1000 copy warning light)

file://\\Serwer\Serwice%20Manuals\Xerox\pages\XD100inf.html

2004-12-21

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: